No abstract

Poly(n-butyl methacrylate) (PBMA) or poly(n-butyl acrylate) (PBA)-grafted brush coatings attached to glass were successfully prepared using atom-transfer radical polymerization "from the surface". The thicknesses and composition of the PBMA and PBA coatings were examined using ellipsometry and time-of-flight secondary ion mass spectrometry (ToF-SIMS), respectively. For PBMA, the glasstransition temperature constitutes a range close to the physiological limit, which is in contrast to PBA, where the glass-transition temperature is around −55 °C. Atomic force microscopy studies at different temperatures suggest a strong morphological transformation for PBMA coatings, in contrast to PBA, where such essential changes in the surface morphology are absent. Besides, for PBMA coatings, protein adsorption depicts a strong temperature dependence. The combination of bovine serum albumin and anti-IgG structure analysis with the principal component analysis of ToF-SIMS spectra revealed a different orientation of proteins adsorbed to PBMA coatings at different temperatures. In addition, the biological activity of anti-IgG molecules adsorbed at different temperatures was evaluated through tracing the specific binding with goat IgG.

PBMA as temperature-responsive and biocompatible coating.

By assembling 140 nm-sized fluorescent nanodiamonds (FNDs) in a thin-film on (3-aminopropyl) triethoxysilane functionalized glass surface, we prepare magnetically-sensitive FND-fiber probes for endoscopy. The obtained FND layers show good uniformity over large surfaces and are characterized using confocal, fluorescence, and atomic force microscopes. Further, FNDs are assembled on single large-core multimode optical fibers and imaging fiber bundles end face to detect optically detectable magnetic resonance (ODMR) signals. The ODMR signals are recorded through the fiber’s far end in magnetic fields between 0 to 2.5 mT. A multi-channel sensor is demonstrated with the capability of parallel-in-time mapping and instantaneous readout from individual pixel and enabling magnetic mapping at high spatial resolution. Results of this study are promising for early stage detection in bio-diagnostic applications.

No abstract

Novel brush coatings were fabricated with glass surface-grafted chains copolymerized using surface-initiated atom transfer radical polymerization (SI-ATRP) from 2-(2-methoxyethoxy)ethyl methacrylate (OEGMA188) and acrylamide (AAm), taken in different proportions. P(OEGMA188-co-AAm) brushes with AAm mole fraction >44% (determined with XPS and TOF-SIMS spectroscopy) and nearly constant with the depth copolymer composition (TOF-SIMS profiling) exhibit unusual temperature-induced transformations: The contact angle of water droplets on P(OEGMA188-co-AAm) coatings increases by ∼45° with temperature, compared to 17–18° for POEGMA188 and PAAm. The thickness of coatings immersed in water and the morphology of coatings imaged in air show a temperature response for POEGMA188 (using reflectance spectroscopy and AFM, respectively), but this response is weak for P(OEGMA188-co-AAm) and absent for PAAm. This suggests mechanisms more complex than a simple transition between hydrated loose coils and hydrophobic collapsed chains. For POEGMA188, the hydrogen bonds between the ether oxygens of poly(ethylene glycol) and water hydrogens are formed below the transition temperature T c and disrupted above T c when polymer–polymer interactions are favored. Different hydrogen bond structures of PAAm include free amide groups, cis-trans-multimers, and trans-multimers of amide groups. Here, hydrogen bonds between free amide groups and water dominate at T < T c but structures favored at T > T c, such as cis-trans-multimers and trans-multimers of amide groups, can still be hydrated. The enhanced temperature-dependent response of wettability for P(OEGMA188-co-AAm) with a high mole fraction of AAm suggests the formation at T c of more hydrophobic structures, realized by hydrogen bonding between the ether oxygens of OEGMA188 and the amide fragments of AAm, where water molecules are caged. Furthermore, P(OEGMA188-co-AAm) coatings immersed in pH buffer solutions exhibit a ‘schizophrenic’ behavior in wettability, with transitions that mimic LCST and UCST for pH = 3, LCST for pH = 5 and 7, and any transition blocked for pH = 9.

No abstract

The surface properties of poly(3,4-ethylenedioxythiophene):(polystyrene sulfonate) (PEDOT:PSS) affect the performance of many organic electronic devices. The work function determines the efficiency of the charge carrier transfer between PEDOT:PSS electrodes and the active layer of the device. The surface free energy affects phase separation in multicomponent blends that are typically used to fabricate active layers of organic light-emitting diodes and photovoltaic devices. Here, we present a method to prepare PEDOT:PSS films with a gradient work function and surface free energy. This modification was achieved by evaporation of trimethoxy(3,3,3-trifluoropropyl)silane in such a way that the degree of surface coverage of the molecules varied in the selected direction. Gradient films were used as electrodes to fabricate two-terminal PEDOT:PSS/poly(3-hexyl thiophene)/Au devices to rapidly screen for the influence of the modification on the performance of the prepared polymer diodes. Gradual changes in the morphology of the solution-cast model poly(3-butyl thiophene)/poly-bromostyrene films followed changes in the surface energy of the substrate.