An integral part of the drive elements of machines in forestry are devices that ensure their protection against breakdowns during overloads. Safety devices can be installed on various parts of the kinematic chain of the machine drive elements: at the beginning, at the end or in the middle, and can also be built into the working unit (body). It is most advisable to install fuses closer to the end of the drive lines of the kinematic chain of the machine. If torque safety devices are installed at the beginning or in the middle of the drive, they are not in the overload zone (more often, overload occurs next to the working unit or directly on it). Under these conditions, the drive links of the kinematic chain are subject to overloads of various magnitudes. With distance from the place of occurrence of overload, the value of the value of the dynamic moment decreases due to elastic deformations and friction losses in the drive links of the machine. Consequently, there is a breakdown or destruction of parts and components of the drive, and the fuse itself does not work. Thus, in this article, using a calculated mathematical model of the actuation process of safety devices using a computer, calculations were carried out to determine the values of dynamic loads and an assessment was given in the case of installing a fuse at the beginning and at the end of the kinematic chain of the machine drive
77850234 УДК 630*4 ПОЛОЖЕНИЯ И ТРЕБОВАНИЯ, ПРЕДЪЯВЛЯЕМЫЕ ПРИ РАЗРАБОТКЕ СРЕДСТВ ЗАЩИТЫ ФРЕЗЕРНЫХ МАШИН ОТ ПЕРЕГРУЗОК С УПРУГИМИ ЭЛЕМЕНТАМИ кандидат технических наук П. Н. Щеблыкин 1 кандидат технических наук Р. Г. Боровиков 1 1-ФГБОУ ВО «Воронежский государственный лесотехнический университет имени Г.Ф. Морозова», г. Воронеж, Российская Федерация В статье представлены основные положения, на которые следует опираться при разработке конструктивных решений приводных узлов лесохозяйственных машин включающих в свою конструкцию предохранительные устройства позволяющих защищать их по крутящему моменту. Отмечено, что особое внимание при конструировании необходимо уделять снижению динамических нагрузок, возникающих в процессе нормальной эксплуатации в течение всего времени работы ротационной лесохозяйственной машины и возникающих при перегрузках в результате срабатывания их предохранительных устройств. Показано, что предохранительные устройства необходимо устанавливать как можно ближе к рабочему органу или непосредственно в нем, без изменения кинетической энергии движущих масс фрезерного барабана. Так же представлены и описаны основные характеристики и виды неметаллических упругих элементов, которые в совокупности с фрикционными элементами, представляющими собой отдельные вкладыши, позволяют преобразовывать обычные предохранительные устройства в упругопредохранительные, и следовательно в дальнейшем применяться при создании новых конструкционных решений ротационных лесохозяйственных машин с активными рабочими органами и их предохранительными устройствами позволяющими уменьшать жесткость и диссипацию системы с достаточной простотой и наименьшими затратами. Ключевые слова: предохранительное устройство, упругий элемент, перегрузка, конструкция.
The reliable operation of tillage forestry cutters largely depends on the perfection of their means of protection against overloads. The safety devices used to protect against overloading of tillage mills by torque do not fully provide adequate protection of working bodies and the drive against arising overloads, since they have significant dynamic loads, low accuracy of operation, complicate the design of the machine, and lead to premature failure of individual its parts and assemblies increase the cost and repair costs. The main criterion for the design of high-quality fuses in design that protect the drive units of the machine in terms of torque is the introduction of such elements into their design that would allow several functions to be performed at once. Thus, this article presents recommendations that will allow the calculation of the main characteristics of the friction type fuses and their elements located in close proximity to the working body of the rotary forestry machine or built into them, having in their design elastic pressing elements of a flat cylindrical shape.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
customersupport@researchsolutions.com
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.