Wearable robots based on soft materials will augment mobility and performance of the host without restricting natural kinematics. Such wearable robots will need soft sensors to monitor the movement of the wearer and robot outside the lab. Until now wearable soft sensors have not demonstrated significant mechanical robustness nor been systematically characterized for human motion studies of walking and running. Here, we present the design and systematic characterization of a soft sensing suit for monitoring hip, knee, and ankle sagittal plane joint angles. We used hyper-elastic strain sensors based on microchannels of liquid metal embedded within elastomer, but refined their design with the use of discretized stiffness gradients to improve mechanical durability. We found that these robust sensors could stretch up to 396% of their original lengths, would restrict the wearer by less than 0.17% of any given joint’s torque, had gauge factor sensitivities of greater than 2.2, and exhibited less than 2% change in electromechanical specifications through 1500 cycles of loading–unloading. We also evaluated the accuracy and variability of the soft sensing suit by comparing it with joint angle data obtained through optical motion capture. The sensing suit had root mean square (RMS) errors of less than 5° for a walking speed of 0.89 m/s and reached a maximum RMS error of 15° for a running speed of 2.7 m/s. Despite the deviation of absolute measure, the relative repeatability of the sensing suit’s joint angle measurements were statistically equivalent to that of optical motion capture at all speeds. We anticipate that wearable soft sensing will also have applications beyond wearable robotics, such as in medical diagnostics and in human–computer interaction.

Abstract-In this paper we present a soft lower-extremity robotic exosuit intended to augment normal muscle function in healthy individuals. Compared to previous exoskeletons, the device is ultra-lightweight, resulting in low mechanical impedance and inertia. The exosuit has custom McKibben style pneumatic actuators that can assist the hip, knee and ankle. The actuators attach to the exosuit through a network of soft, inextensible webbing triangulated to attachment points utilizing a novel approach we call the virtual anchor technique. This approach is designed to transfer forces to locations on the body that can best accept load. Pneumatic actuation was chosen for this initial prototype because the McKibben actuators are soft and can be easily driven by an off-board compressor. The exosuit itself (human interface and actuators) had a mass of 3500 g and with peripherals (excluding air supply) is 7144 g. In order to examine the exosuit's performance, a pilot study with one subject was performed which investigated the effect of the ankle plantar-flexion timing on the wearer's hip, knee and ankle joint kinematics and metabolic power when walking. Wearing the suit in a passive unpowered mode had little effect on hip, knee and ankle joint kinematics as compared to baseline walking when not wearing the suit. Engaging the actuators at the ankles at 30% of the gait cycle for 250 ms altered joint kinematics the least and also minimized metabolic power. The subject's average metabolic power was 386.7 W, almost identical to the average power when wearing no suit (381.8 W), and substantially less than walking with the unpowered suit (430.6 W). This preliminary work demonstrates that the exosuit can comfortably transmit joint torques to the user while not restricting mobility and that with further optimization, has the potential to reduce the wearer's metabolic cost during walking.

No abstract

In this paper, we present the design of a thumb exoskeleton for pediatric at-home rehabilitation. Pediatric disorders, such as cerebral palsy (CP) and stroke, can result in thumb in palm deformity greatly limiting hand function. This not only limits children's ability to perform activities of daily living but also limits important motor skill development. Specifically, the device, dubbed IOTA (Isolated Orthosis for Thumb Actuation) is a 2-DOF thumb exoskeleton that can actuate the carpometacarpal (CMC) and metacarpalphalangeal (MCP) joints through ranges of motion required for activities of daily living. The device consists of a lightweight hand-mounted mechanism that can be custom secured and aligned to the wearer. The mechanism is actuated via flexible cables that connect to a portable control box. Embedded encoders and bend sensors monitor the two degrees of freedom of the thumb and flexion/extension of the wrist. Using this platform, a number of control modes can be implemented that will enable the device to be intuitively controlled by a patient to assist with opposition grasp, fine motor control, and ultimately facilitate motor recovery. We envision this at-home device augmenting the current in-clinic therapy and enabling tele-rehabilitation where a clinician can remotely monitor a patient's usage and performance.

No abstract

Our findings support the hypothesis that an angle-pressure relationship exists following arthrodesis of the first metatarsophalangeal joint and that it is inversely related for the hallux and the metatarsal head. Our results encompass the suggested range of 20 degrees to 25 degrees.

Abstract-Motion sensing has played an important role in the study of human biomechanics as well as the entertainment industry. Although existing technologies, such as optical or inertial based motion capture systems, have relatively high accuracy in detecting body motions, they still have inherent limitations with regards to mobility and wearability. In this paper, we present a soft motion sensing suit for measuring lower extremity joint motion. The sensing suit prototype includes a pair of elastic tights and three hyperelastic strain sensors. The strain sensors are made of silicone elastomer with embedded microchannels filled with conductive liquid. To form a sensing suit, these sensors are attached at the hip, knee, and ankle areas to measure the joint angles in the sagittal plane. The prototype motion sensing suit has significant potential as an autonomous system that can be worn by individuals during many activities outside the laboratory, from running to rock climbing. In this study we characterize the hyperelastic sensors in isolation to determine their mechanical and electrical responses to strain, and then demonstrate the sensing capability of the integrated suit in comparison with a ground truth optical motion capture system. Using simple calibration techniques, we can accurately track joint angles and gait phase. Our efforts result in a calculated trade off: with a maximum error less than 8%, the sensing suit does not track joints as accurately as optical motion capture, but its wearability means that it is not constrained to use only in a lab.

We have developed a robotic gait simulator (RGS) by leveraging a 6-degree of freedom parallel robot, with the goal of overcoming three significant challenges of gait simulation, including: 1) operating at near physiologically correct velocities; 2) inputting full scale ground reaction forces; and 3) simulating motion in all three planes (sagittal, coronal and transverse). The robot will eventually be employed with cadaveric specimens, but as a means of exploring the capability of the system, we have first used it with a prosthetic foot. Gait data were recorded from one transtibial amputee using a motion analysis system and force plate. Using the same prosthetic foot as the subject, the RGS accurately reproduced the recorded kinematics and kinetics and the appropriate vertical ground reaction force was realized with a proportional iterative learning controller. After six gait iterations the controller reduced the root mean square (RMS) error between the simulated and in situ; vertical ground reaction force to 35 N during a 1.5 s simulation of the stance phase of gait with a prosthetic foot. This paper addresses the design, methodology and validation of the novel RGS.