We report a dispersion polymerization method based on thiol−Michael addition reactions for the preparation of cross-linked, narrow dispersity microparticles with well-defined, tunable physicochemical properties. Polymerization between pentaerythritol tetra(3-mercaptopropionate) (PETMP) and trimethylolpropane triacrylate in methanol was chosen as a model system, with the addition of triethylamine as a catalyst and polyvinylpyrrolidone as a stabilizer. The formation of microparticles took place within seconds at ambient conditions, as a result of a polymerization driven phase transition from dissolved monomers to precipitated polymers. The particle size was found to be affected by the amount of catalyst, the monomer concentration, and the monomer/polymer solubility in the reaction media. Monodispersity was achieved within a range of particle diameters from 1.6 to 4.3 μm, as determined both by scanning electron microscopy and dynamic light scattering. The reaction kinetics were studied by Fourier transform infrared spectroscopy by analyzing aliquots withdrawn from the reaction system at various reaction time points. Nearly quantitative conversions were achieved within 6 h for stoichiometric systems and 1 h for off-stoichiometric systems, both initiated with triethylamine. By utilizing photolabile bases as the reaction catalyst, phototriggered formation of the microparticles was demonstrated with ultraviolet irradiation. Monodisperse particles were formed with hexylamine and 1,1,3,3-tetramethylguanidine, both with 2-(2-nitrophenyl)propyloxycarbonyl as the UV-labile photocage. Furthermore, as a demonstration of the versatility of this method, microparticles were prepared from copolymerizations between PETMP and four types of diacrylates with varied backbone structures. With increased backbone rigidity, the microparticle glass transition temperature increased from −36 to 8 °C. This method provides a platform for the realization of the nearly ideal step-growth networks in microscale, with highly tunable backbone structures, robust thermal transitions, and intrinsic functionalization capacity.

No abstract

Objectives To detail the development of ester-free thiol-ene dental resins with enhanced mechanical performance, limited potential for water uptake/leachables/degradation and low polymerization shrinkage stress. Methods Thiol-terminated oligomers were prepared via a thiol-Michael reaction and a bulky tetra-allyl monomer containing urethane linkages was synthesized. The experimental oligomers and/or monomers were photopolymerized using visible light activation. Several thiol-ene formulations were investigated and their performance ranked by comparisons of the thermo-mechanical properties, polymerization shrinkage stress, water sorption/solubility, and reactivity with respect to a control comprising a conventional BisGMA/TEGDMA dental resin. Results The ester-free thiol-ene formulations had significantly lower viscosities, water sorption and solubility than the BisGMA/TEGDMA control. Depending on the resin, the limiting functional conversions were equivalent to or greater than that of BisGMA/TEGDMA. At comparable conversions, lower shrinkage stress values were achieved by the thiol-ene systems. The polymerization shrinkage stress was dramatically reduced when the tetra-allyl monomer was used as the ene in ester-free thiol-ene mixtures. Although exhibiting lower Young’s modulus, flexural strength, and glass transition temperatures, the toughness values associated with thiol-ene resins were greater than that of the BisGMA/TEGDMA control. In addition, the thiol-ene polymerization resulted in highly uniform polymer networks as indicated by the narrow tan delta peak widths. Significance Employing the developed thiol-ene resins in dental composites will reduce shrinkage stress and moisture absorption and form tougher materials. Furthermore, their low viscosities are expected to enable higher loadings of functionalized micro/nano-scale filler particles relevant for practical dental systems.

A scalable synthesis of high refractive index, optically transparent photopolymers from a family of low-viscosity multifunctional thiol and alkyne monomers via thiol−yne "click" is described herein. The monomers designed to incorporate high refractive index cores consisting of aryl and sulfide groups with high intrinsic molar refraction were synthesized starting from commercially available low-cost raw materials. The low-viscosity (<500 cP) thiol−yne resins formulated with these new multifunctional monomers and a phosphine oxide photoinitiator underwent efficient thiol−yne polymerizations upon exposure to 405 nm light at 30 mW/cm 2 . In contrast to the previously reported thiol−ene systems, the kinetic profile of these photopolymerizations showed significant dependence on the nature of the thiol and alkyne monomers. However, the ability of the thiol−yne reaction to introduce a large number of sulfide linkages compared to that of thiol− ene systems yielded cross-linked high optical quality photopolymers with a polymer refractive index that exceeds 1.68 (n D /20 °C). Interestingly, the photopolymer formed from the least sterically hindered alkynyl thioether monomer 2b with flexible thioether core and the dithiol 1a exhibited unprecedented difference in the polymer refractive index as compared to that of the resin with polymerization-induced changes reaching up to 0.08. Furthermore, the implementation of these low-viscosity thiol−yne resins was demonstrated by preparing two-stage photopolymeric holographic materials with a dynamic range of ∼0.02 and haze < 1.5% in twodimensional high refractive index structures.

Glutamine synthetase (GS) regulation in Escherichia coli by reversible covalent modification cycles is a prototype of signal transduction by enzyme cascades. Such enzyme cascades are known to exhibit ultrasensitive response to primary stimuli and act as signal integration systems. Here, we have quantified GS bicyclic cascade based on steady state analysis by evaluating Hill coefficient. We demonstrate that adenylylation of GS with glutamine as input is insensitive to total enzyme concentrations of GS, uridylyltransferase/uridylyl-removing enzyme, regulatory protein PII, and adenylyltransferase/adenylyl-removing enzyme. This robust response of GS adenylylation is also observed for change in system parameters. From numerical analyses, we show that the robust ultrasensitive response of bicyclic cascade is because of allosteric interactions of glutamine and 2-ketoglutarate, bifunctionality of converter enzymes, and closed loop bicyclic cascade structure. By system level quantification of the GS bicyclic cascade, we conclude that such a robust response may help the cell in adapting to different carbon and nitrogen status.

This work examined and quantitatively predicted the degradation of thioester-containing networks facilitated by base-catalyzed thiol−thioester exchange. A statistical model was developed that incorporated polymer structure, thiol−thioester exchange reaction kinetics, and mass gain resulting from dynamic bond exchange, and this model was compared to mass loss studies. Experimental results matched model predictions, showing that degradation times could be controlled from 2.5 to 12 h with optimal conditions by varying the free thiol butyl 3-mercaptopropionate concentration from 0.0 to 4.9 M and the base-catalyst triethylamine molar ratio from 0 to 40 mol %. Furthermore, thioester-based composite materials were formed by stereolithography (SLA) three dimensional (3-D) printing and subsequently degraded, achieving 91% recovery of the composite filler. This work provides insight into thioester-facilitated degradation and its future use in selective material release or encapsulated filler recovery applications.

The interfacial region in composites that incorporate filler materials of dramatically different modulus relative to the resin phase acts as a stress concentrator and becomes a primary locus for composite failure. A novel adaptive interface (AI) platform formed by coupling moieties capable of dynamic covalent chemistry (DCC) is introduced to the resin–filler interface to promote stress relaxation. Specifically, silica nanoparticles (SNP) are functionalized with a silane capable of addition fragmentation chain transfer (AFT), a process by which DCC-active bonds are reversibly exchanged upon light exposure and concomitant radical generation, and copolymerized with a thiol-ene resin. At a fixed SNP loading of 25 wt%, the toughness (2.3 MJ m−3) is more than doubled and polymerization shrinkage stress (0.4 MPa) is cut in half in the AI composite relative to otherwise identical composites that possess a passive interface (PI) with similar silane structure, but without the AFT moiety. In situ activation of the AI during mechanical loading results in 70% stress relaxation and three times higher fracture toughness than the PI control. When interfacial DCC was combined with resin-based DCC, the toughness was improved by 10 times relative to the composite without DCC in either the resin or at the resin–filler interface.

A new addition-fragmentation chain transfer (AFT) capable moiety was incorporated into a dimethacrylate monomer that participated readily in network formation by copolymerizing with multifunctional methacrylates or acrylates. The process of AFT occurred simultaneously with photopolymerization of the AFT monomer (AFM) and other (meth)acrylate monomers leading to polymer stress relaxation via network reconfiguration. At low loading levels of the AFM, a significant reduction in shrinkage stress, especially for acrylate monomers, was observed with nominal effects on conversion. At higher loading levels of the AFM, the photopolymerization reaction kinetics and final double bond conversion were significantly lowered along with a delay in the gel-point conversion. Electron paramagnetic resonance studies during polymerization revealed the presence of a distinct radical species that was present in proportional quantities to the AFM content in the system. The lifetime and the character of the persistent radicals were altered due to the presence of the distinctive radical, in turn affecting the polymerization kinetics. With polymerization conducted at higher irradiance, the differential conversion between the control resin and samples with moderate AFM content was minimal, especially for the methacrylate-based formulations.