Highlights pH-sensitive PCL and PCL/chitosan nanofibres are successfully electrospun. pH-sensitive PCL and PCL/chitosan nanofibres show a clear halochromic response. Chitosan addition results in a significantly increased water sorption. Chitosan addition is indispensable for a sensitive and rapid response. Theoretical modelling on the dye-polymer interactions underpins the experimental findings. Highlights (for review)Polycaprolactone and polycaprolactone/chitosan nanofibres functionalised with pH- Polycaprolactone (PCL) is an aliphatic polyester, often used in (bio)medical applications 56 because of its biocompatibility, slow biodegradability, low-cost, non-toxicity and good 57 mechanical properties (Moghe et al., 2009; Van der Schueren et al., 2011). However, PCL is Prabhakaran et al., 2008;Yang et al., 2009; Bhattarai et al., 2009; Hong & Kim, 2011; 63 Cooper et al., 2011). Contact angle measurements were carried out with the drop-shape analysis system DSA 10- 168Mk2, coupled to a control unit G120 Mk1/G140-Mk1 and with the drop-shape analysis 169 software DSA1 (v1.80, Krüss). 171Dynamic Vapour Sorption (DVS) measurements were conducted in a Q-5000SA instrument 172(TA-instruments, Zellik, Belgium). All measurements were performed at 23 °C ± 0.1 °C. 173Deliquescent salts (sodium bromide and potassium chloride) were used to verify the humidity 174 of the instrument. 4 mg of nanofibres were placed in the quartz sample pans. At the start of 175 each moisture sorption cycle, the fibres were dried at 0 % relative humidity (RH) until the 176 weight change was stabilised to be less than 0.05 % for a period of 15 minutes. After the 177 stabilisation, the moisture sorption cycle was started and the humidity was increased hydroxide were used to adjust the pH. 196The UV-Vis spectra were recorded with a Perkin-Elmer Lambda 900 spectrophotometer. For suggests an increased interaction with water when chitosan blend nanofibres are used. 287As a final step prior to the halochromic study, the dye leaching of the samples is 288 characterised ( The nanofibrous samples were all yellow just after the electrospinning process, in agreement 306 with the acidic conditions during their production (acetic acid-formic acid solvent system). compared to the sharp transition of NY in aqueous solutions, which occurs between pH 6 and 346 8 (Fig. 3a), the response of PCL nanofibres is less sensitive (response between pH 4 and 10, observed. All PCL/chitosan samples showed a sharp transition between pH 4 and 6 (Fig. 3c). 362Also the wavelength maxima did not alter and remained constant at 474 nm and 605 nm in proposed, which will then be validated by theoretical results. After electrospinning pure PCL (Fig. 5b) with NY, no halochromic behaviour is observed, structures. The chitosan model (Fig. 5e) has a PA of 908 kJ/mol, which is much higher than 429 the value of 841 kJ/mol obtained for the PCL model (Fig. 5d). This suggests that the chitosan ( Fig. 7) is much higher, -132.3 kJ/mol. The value for dye leaching was, however, much larger...
Electrospinning is a process to generate a nanofibrous material. Although the working principle of electrospinning is rather straight forward, it is influenced by many parameters. There is still a serious lack of knowledge concerning the influence of the ambient parameters, for which preliminary knowledge reveals that the relative humidity is of primary importance. This article reports the influence of the relative humidity on electrospun polyamide 6 nanofibres. Mixtures of formic acid and acetic acid are used for steady state electrospinning of polyamide 6 nanofibres, for which a steady state table is determined. When the relative humidity increases, the average fiber diameter decreases and the fraction of the less stable c-phase crystals in the polyamide diminishes. This effect is explained by absorbed water acting as a plasticizer, reducing the Tg of the polyamide. This article shows the importance of working in climatized conditions during electrospinning to obtain reproducible nanofibres.
SUMMARYThe aim of this paper is to study the combustion characteristics of loose fibrous cellulosic compounds through cone calorimeter measurements. The challenge in studying loose fibrous materials by cone calorimeter in a reproducible manner is met by optimizing various process parameters such as sample weight, heat flux and grid type. The method is validated using cotton fibres and fabrics with a range of flame retardant properties. Good correlations are obtained between the flame retardant content of samples and the heat release parameters for both the fibres and the fabrics. In addition, fibres from specific cotton cultivars showed statistically significant differences in heat release characteristics. This shows that valuable data concerning the combustion behaviour and the corresponding kinetics of loose fibrous compounds can be successfully gathered using a cone calorimeter. Thus, such data can be exploited to well define future fibre breeding programmes or fibre modification research.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.