The drag coefficient and the laminar-to-turbulent transition for the aerofoil component of a wing model are optimised using an adaptive upper surface with two actuation points. The effects of the new shaped aerofoils on the global drag coefficient of the wing model are also studied. The aerofoil was optimised with an 'in-house' genetic algorithm program coupled with a cubic spline aerofoil shape reconstruction and XFoil 6.96 open-source aerodynamic solver. The wing model analysis was performed with the open-source solver XFLR5 and the 3D Panel Method was used for the aerodynamic calculation. The results of the aerofoil optimisation indicate improvements of both the drag coefficient and transition delay of 2% to 4%. These improvements in the aerofoil characteristics affect the global drag of the wing model, reducing it by up to 2%. The analyses were conducted for a single Reynolds number and speed over a range of angles of attack. The same cases will also be used in the experimental testing of the manufactured morphing wing model.

No abstract

No abstract

A new wing-tip concept with morphing upper surface and interchangeable conventional and morphing ailerons was designed, manufactured, bench and wind-tunnel tested. The development of this wing-tip model was performed in the frame of an international CRIAQ project, and the purpose was to demonstrate the wing upper surface and aileron morphing capabilities in improving the wing-tip aerodynamic performances. During numerical optimisation with ‘in-house’ genetic algorithm software, and during wind-tunnel experimental tests, it was demonstrated that the air-flow laminarity over the wing skin was promoted, and the laminar flow was extended with up to 9% of the chord. Drag coefficient reduction of up to 9% was obtained when the morphing aileron was introduced.

The lifting-line theory is widely used for obtaining aerodynamic performance results in various engineering fields, from aircraft conceptual design to wind-power generation. Many different models were proposed, each tailored for a specific purpose, thus having a rather narrow applicability range. This paper presents a general lifting-line model capable of accurately analysing a wide range of engineering problems involving lifting surfaces, both steady-state and unsteady cases. It can be used for lifting surface with sweep, dihedral, twisting and winglets and includes features such as non-linear viscous corrections, unsteady and quasi-steady force calculation, stable wake relaxation through fictitious time marching and wake stretching and dissipation. Possible applications include wing design for low-speed aircraft and unmanned aerial vehicles, the study of high-frequency avian flapping flight or wind-turbine blade design and analysis. Several validation studies are performed, both steady-state and unsteady, the method showing good agreement with experimental data or numerical results obtained with more computationally expensive methods.

An experimental validation of an optimised wing geometry in the Price-Païdoussis subsonic wind tunnel is presented. Two wing models were manufactured using optimised glass fibre composite and tested at three speeds and various angle-of-attack. These wing models were constructed based on the original aerofoil shape of the ATR 42 aircraft and an optimised version of the same aerofoil for a flight condition of Mach number equal to 0.1 and angle-of-attack of 0°. The aerofoil's optimisation was realised using an ‘in-house’ genetic algorithm coupled with a cubic spline reconstruction routine, and was analysed using XFoil aerodynamic solver. The optimisation was concentrated on improving the laminar flow on the upper surface of the wing, between 10% and 70% of the chord. XFoil-predicted pressure distributions were compared with experimental data obtained in the wind tunnel. The transition position was estimated from the experimental pressure data using a second derivative methodology and was compared with the transition predicted by XFoil code. The results have shown the agreement between numerical and experimental data. The wind-tunnel tests have shown that the improvement of the laminar flow of the optimised wing is higher than the value predicted numerically.

No abstract

/npsi/ctrl?action=rtdoc&an=21277526&lang=en http://nparc.cisti-icist.nrc-cnrc.gc.ca/npsi/ctrl?action=rtdoc&an=21277526&lang=fr READ THESE TERMS AND CONDITIONS CAREFULLY BEFORE USING THIS WEBSITE.http://nparc.cisti-icist.nrc-cnrc.gc.ca/npsi/jsp/nparc_cp.jsp?lang=en Vous avez des questions? Nous pouvons vous aider. Pour communiquer directement avec un auteur, consultez la première page de la revue dans laquelle son article a été publié afin de trouver ses coordonnées. Si vous n'arrivez pas à les repérer, communiquez avec nous à PublicationsArchive-ArchivesPublications@nrc-cnrc.gc.ca. Questions? Contact the NRC Publications Archive team atPublicationsArchive-ArchivesPublications@nrc-cnrc.gc.ca. If you wish to email the authors directly, please see the first page of the publication for their contact information. NRC Publications Archive Archives des publications du CNRCThis publication could be one of several versions: author's original, accepted manuscript or the publisher's version. / La version de cette publication peut être l'une des suivantes : la version prépublication de l'auteur, la version acceptée du manuscrit ou la version de l'éditeur. For the publisher's version, please access the DOI link below./ Pour consulter la version de l'éditeur, utilisez le lien DOI ci-dessous. This paper presents the results obtained from the numerical simulation and experimental wind tunnel testing of a morphing wing equipped with a flexible upper surface and controllable actuated aileron. The technology demonstrator is representative of a real aircraft wing tip section, and it was developed following a complex, multidisciplinary design process. The model was fitted with a composite material upper skin whose shape can be morphed, as a function of the flight condition, by four electrical actuators placed inside the wing structure. The optimizations were performed with the aim of controlling the extent of the laminar flow region, and the resulting shapes were scanned using high-precision photogrammetry. The numerical simulations were performed using Computational Fluid Dynamics (CFD) and included a model for predicting the laminar-to-turbulent flow transition over the entire wing surface. The analyses included cases with three aileron deflection angles and angles of attack situated within five degrees range. The CFD results were compared with infrared thermography measurements in terms of transition location, surface pressure measurements and balance loads measurements acquired during subsonic wind tunnel tests performed at the National Research Council Canada.