No abstract

The application of thermoplastic composites (TPCs) in aircraft application is expanding. This paper presents a study of the effect of layering thickness of Carbon Fibre Reinforced Polyphenylene Sulfide, CF/PPS. There are 2 thickness of plies which are 6 plies and 8 plies of 1.90 mm and 2.52 mm respectively. To update, the aircraft is now ready to shift from thermoset to thermoplastics composite materials. In parallel to the technology, mechanical, thermal and physical properties of the advanced thermoplastic materials CF/PPS are to be determined. By having towards the behavior and properties, thus the incoming material CF/PPS data could be compared to the current nominal of epoxy thermoset structural for aircraft which is benefit to the aircraft industries purpose. In this study, it was found that, for mechanical properties, Tensile Strength, Flexural Modulus as well as Vickers Hardness recorded 6 plies higher value compared to 8 plies. While, Impact Strength, Interlaminar Shear Strength, (ILSS) and Compressive Strength shown that 8 plies obtained the superior reading compared to 6 plies. For physical properties, the density of 6 plies and 8 plies recorded 1.541 and 1.547 respectively. Content as a percentage of the initial mass of fibre, (%) recorded 6 plies was 58.397% while 8 plies was 58.235 %. Fibre content as a percentage of the initial volume, (%) recorded 6 plies was 50.838% while 8 plies was 50.885%. Void content as a percentage of the initial volume, (%) recorded 6 plies was 1.678% while 8 plies was 1.268%. While, for the thermal analysis, both samples of CF/PPS have good thermal stability material in aerospace applications as the weight for both plies CF/PPS are observed as the function of temperature (high heat energy applied). Glass Transition Temperature ( was 93.75°C for 6 plies while 8 plies recorded 93.94°C. Melting Temperature, recorded 283.68°C for 6 plies whereas 283.61°C for 8 plies. The morphological analysis under Scanning Electron Microscope (SEM) shows that 6 plies had a lot of fibre pull out compared to 8 plies thus agreed that impact strength was higher on 8 plies over 6 plies.

In the study, the photovoltaic thermal system using nanofluid as coolant is validated using numerical approach by comparing the experimental results and simulation results. Due to high cost and difficulty in preparing nanofluid, it is more practical to perform the study using numerical approach which is convenient and saves plenty of time. The photovoltaic thermal system is investigated numerically through Computational Fluid Dynamics Approach using Ansys 19.0 Fluent Software. The numerical study is based on different solar irradiation at different hours. The coolant that is selected in the study is aluminum oxide () water nanofluid. The validation study between the experimental results and simulation results are achieved by examining the photovoltaic (PV) surface temperature and nanofluid outlet temperature. The maximum percentage of error between experimental and simulation results of PV surface temperature and nanofluid outlet temperature are 12.66% and 7.89%. Also, the mean average percentage error (MAPE) are computed for PV surface temperature and nanofluid outlet temperature. The results for PV surface temperature and nanofluid outlet temperature are 10.31% and 6.67%. Since the MAPE results are within 10% or error, it proved that there is good accuracy between the simulation and experimental results.

Aerospace industry is seeking thermoplastic composites materials due to several advantages over thermoset material and one of them is mechanical properties. Mechanical properties of thermoplastic composite materials are found to be superior compared to thermoset materials. High strength fibre composites parts are made of several plies with different fibre orientation with a designed balanced of lay-up sequence. Interlaminar Shear Strength (ILSS) is an essential consideration when designing laminated structures exposed to transverse stresses. It is to predict quality and strength of laminate levels of composite due to, composite failure cannot be observed directly to the propagation of single macroscopic crack when subjected to cyclic loading. This test is employed to evaluate both the interfacial adhesion of the matrix and the influence of the reinforcement on the mechanical characteristics of the composite. This study provides the understanding of ILSS test of 2 different thickness for 6 and 8 plies Carbon Fibre Reinforced Polyphenylene Sulfide (CF/PPS) according to the testing standard EN 2563. The results show that 8 plies have higher ILSS properties compared to 6 plies. The fractography of the CF/PPS composite under Scanning Electron Microscope (SEM) shows good agreement with the experimental values which was recorded 8 plies can withstand to shear strength of 79 MPa with maximum load applied was 2.738kN while, 6 plies recorded 75 MPa on shear strength with load of 1.971kN. More damage/cracks on 6 plies specimen compared to 8 plies.

Membrane distillation (MD) performance in seawater desalination can be improved by enhancing the material properties (hydrophobicity, porosity) and process parameters (feed flow rate, temperature). In this study, the effects of hydrophobic silica loading on the properties and MD performance of a polyvinylidene difluoride‐based membrane in seawater desalination were investigated, and a sensitivity analysis (temperature gradient, feed flow rate, salinity) was performed. Incorporation of hydrophobic silica improved the hydrophobicity of the membrane. Higher filler loading increased the number of surface pores while maintaining their size. This resulted in improved flux compared with the neat membrane while maintaining high salt rejection. The optimized membrane was 73 % more efficient than the neat membrane.

No abstract

Recently, an interest of thermoelectric generator (TEG) to manipulate and change heat waste into electrical energy has increased. The heat from electrical appliances, sun, human body, and natural environments can convert into electrical energy using TEG. However, typical conventional TEGs in the market have a hard and solid construction structure, hence difficult to bend according to curved surfaces of the heat sources. To overcome this problem, polymer-based material is proposing as the new packaging and substrate structure for the TEG. Besides, the thermoelectric conductor layer also changed using different types of pyroelectric for better heat absorption performance with low cost in mass-scale fabrication. Therefore, the simulation of eight pairs segmented conductive layer insulated with thin-film polymer due to standard modelling equation is present. The comparison of simulation with reference TEG to get the optimum output of temperature difference were also explaining. At the end of the simulation, polyimide as a packaging substrate with a conductive layer of Graphene (P-type legs) and Bismuth Telluride (N-type legs) has chosen for the best performance material for the flexible thermoelectric generator. The highest temperature difference produced by this design is 542˚C for 0.945V input voltage and 120˚C input temperature at the hot side.