No abstract

The results of the present study showed that the clinical use of an Er:YAG laser resulted in a smooth root surface morphology, even at higher energy settings. The results also seem to indicate that calculus removal can be selectively done in vivo.

SUMMARYRoot contraction has been described for many species within the plant kingdom for over a century, and many suggestions have been made for mechanisms behind these contractions. To move the foliage buds deeper into the soil, the proximal part of the storage root of Trifolium pratense contracts by up to 30%. Anatomical studies have shown undeformed fibres next to strongly deformed tissues. Raman imaging revealed that these fibres are chemically and structurally very similar to poplar (Populus) tension wood fibres, which are known to generate high tensile stresses and bend leaning stems or branches upright. Analogously, an almost pure cellulosic layer is laid down in the lumen of certain root fibres, on a thin lignified secondary cell wall layer. To reveal its stress generation capacities, the thick cellulosic layer, reminiscent of a gelatinous layer (G-layer) in tension wood, was selectively removed by enzymatic treatment. A substantial change in the dimensions of the isolated wood fibre bundles was observed. This high stress relaxation indicates the presence of high tensile stress for root contraction. These findings indicate a mechanism of root contraction in T. pratense (red clover) actuated via tension wood fibres, which follows the same principle known for poplar tension wood.

Hydroxyapatite nanoparticles (nano-HAP) are receiving considerable attention for dental applications, and their adhesion to enamel is well established. However, there are no reports concerning the effects of HAP on other dental materials, and most of the studies in this field are based on in vitro designs, neglecting the salivary pellicle-apatite interactions. Thus, this in situ pilot study aims to evaluate the effects of three hydroxyapatite-based solutions and their interactions with different dental material surfaces under oral conditions. Hence, two volunteers carried intraoral splints with mounted samples from enamel and from three dental materials: titanium, ceramics, and polymethyl-methacrylate (PMMA). Three HAP watery solutions (5%) were prepared with different shapes and sizes of nano-HAP (HAP I, HAP II, HAP III). After 3 min of pellicle formation, 10 ml rinse was performed during 30 sec. Rinsing with water served as control. Samples were accessed immediately after rinsing, 30 min and 2 h after rinsing. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were used to characterize the particles, and SEM evaluated the pellicle-HAP interactions. SEM and TEM results showed a high variation in the size range of the particles applied. A heterogeneous HAP layer was present after 2 h on enamel, titanium, ceramics, and PMMA surfaces under oral conditions. Bridge-like structures were visible between the nano-HAP and the pellicle formed on enamel, titanium, and PMMA surfaces. In conclusion, nano-HAP can adhere not only to enamel but also to artificial dental surfaces under oral conditions. The experiment showed that the acquired pellicle act as a bridge between the nano-HAP and the materials’ surface.

The present clinical-experimental study aims to examine the effect of pure experimental fluoride solutions and stannous chloride on the initial oral bioadhesion under in situ conditions. After 1 min of pellicle formation on bovine enamel slabs, 12 subjects rinsed with 8 ml of the fluoride test solutions (NaF, Na2PO3F, AmF, SnF2,) with 500 ppm fluoride concentration each for 1 min. Additionally, rinsing without a solution (control) and rinsing with 1563 ppm SnCl2 solution took place for 1 min. Afterwards, fluorescence microscopy took place to visualize bacterial adhesion and glucan formation (8 h oral exposition) with DAPI and ConA and the BacLight method. TEM was performed to visualize the pellicle ultrastructure together with EDX to detect stannous ions. The rinsing solutions with pure SnF2 and SnCl2 reduced significantly the initial bacterial colonization (DAPI). While, NaF and Na2PO3F showed no significant effect compared to the control. There was no significant difference between AmF, SnF2 and SnCl2. All tested experimental solutions showed no reducing effect on the glucan formation. Considerable alterations of the pellicle ultrastructure resulted from rinsing with the Sn-containing solutions. SnF2 appears to be the most effective type of fluoride to reduce initial bacterial colonization in situ. The observed effects primarily have to be attributed to the stannous ions’ content.

The surface charge of a biomaterial represents a promising tool to direct cellular behavior, which is crucial for therapeutic approaches in regenerative medicine. To expand the understanding of how the material surface charge affects protein adsorption and mesenchymal stem cell behavior, differently charged surfaces with zeta potentials spanning from −25 mV to +15 mV were fabricated by the conjugation of poly(amidoamine) to alginate-based hydrogels. We showed that the increase of the biomaterials surface charge resulted in enhanced quantities of biologically available, surface-attached proteins. Since different surface charges were equalized after protein adsorption, mesenchymal stem cells interacted rather with diverse protein compositions instead of different surface features. Besides an enhanced cell attachment to increasingly positively charged surfaces, the cell spreading area and the expression of adhesion-related genes integrin α5 and tensin 1 were found to be increased after adhesion. Moreover, first results indicate a potential impact of the surface charge on mesenchymal stem cell differentiation towards bone and fat cells. The improved understanding of surface charge-related cell behavior has significant impact on the design of biomedical devices and artificial organs.

No abstract

No abstract