This article reports an experimental assessment of surface quality generated in the precision turning of AISI 4340 steel alloy using conventional round and wiper nose inserts for different cutting conditions. A three-factor (each at 4 levels) full factorial design of experiment was followed for feed rate, cutting speed, and depth of cut, with resulting machined surface quality characterized by resulting average roughness (Ra). The results show that, for the provided range of cutting conditions, lower surface roughness values were obtained using wiper inserts compared with conventional inserts, indicating a superior performance. When including the type of insert as a qualitative factor, ANOVA revealed that the type of insert was most important in determining surface roughness and material removal rate, with feed rate as the second most significant, followed by the interaction of feed rate and type of insert. It was found that using wiper inserts allowed simultaneous increases in feed rate, cutting speed, and depth of cut, while providing better surface quality of lower Ra, compared to the global minimum value that could be achieved using the conventional insert. These findings show that wiper inserts produce better surface quality and a material removal rate up to ten times higher than that obtained with conventional inserts. This clearly indicates the tremendous advantages of high surface quality and productivity that wiper inserts can offer when compared with the conventional round nose type in precision hard turning of AISI 4340 alloy steel.

No abstract

No abstract

This paper reports a fundamental investigation consisting of systematic trials into the response of Ti6Al4V alloy to high-speed machining using carbide inserts. It is a useful extension to work previously published, and aims at assessing the impact of the process parameters, depth of cut, cutting speed and feed rate in addition to cutting length, and their interrelations, on observed crater and flank wear and roughness of the machined surface. The results showed that abrasion was the most important flank wear mechanism at high speed. It also showed that increased cutting length accelerated crater wear more than exhibited flank wear and had considerable effect on surface roughness. In particular, crater wear increased by over 150% (on average), and flank wear increased by 40% (on average) when increasing cutting length from 40 to 120 mm. However, cutting the same length increased surface roughness by 50%, which helps explain how progression of tool wear leads to deteriorated surface quality. ANOVA was used to perform statistical analyses of the measured data and revealed that cutting length and depth of cut had the greatest effect on both crater and flank wear of the cutting tool. These results confirm that high-speed machining of Ti6Al4V alloy is a reliable process, with cutting speed identified as having a relatively small influence on the tool wear and resultant roughness of the machined surface relative to other parameters.

Its unexcelled mechanical and physical properties, in addition to its biocompatibility, have made stainless steel 304 a prime candidate for a wide range of applications. Among different manufacturing techniques, electrical discharge machining (EDM) has shown high potential in processing stainless steel 304 in a controllable manner. This paper reports the results of an experimental investigation into the effect of the process parameters on the obtainable surface roughness and material removal rate of stainless steel 304, when slotted using wire EDM. A full factorial design of the experiment was followed when conducting experimental trials in which the effects of the different levels of the five process parameters; applied voltage, traverse feed, pulse-on time, pulse-off time, and current intensity were investigated. The geometry of the cut slots was characterized using the MATLAB image processing toolbox to detect the edge and precise width of the cut slot along its entire length to determine the material removal rate. In addition, the surface roughness of the side walls of the slots were characterized, and the roughness average was evaluated for the range of the process parameters being examined. The effect of the five process parameters on both responses were studied, and the results revealed that the material removal rate is significantly influenced by feed (p-value = 9.72 × 10−29), followed by current tension (p-value = 6.02 × 10−7), and voltage (p-value = 3.77 × 10−5), while the most significant parameters affecting the surface roughness are current tension (p-value = 1.89 × 10−7), followed by pulse-on time (1.602 × 10−5), and pulse-off time (0.0204). The developed regression models and associated prediction plots offer a reliable tool to predict the effect of the process parameters, and thus enable the optimizing of their effects on both responses; surface roughness and material removal rate. The results also reveal the trade-off between the effect of significant process parameters on the material removal rate and surface roughness. This points out the need for a robust multi-objective optimization technique to identify the process window for obtaining high quality surfaces while keeping the material removal rate as high as possible.