A promising path for introducing rapid modulation into fibres would be through the piezoelectric effect [10][11] . Embedding piezoelectric domains would allow fibres to be electrically actuated over broad frequencies on the one hand, and to function as sensitive broadband microphones on the other. However, fibres for the most part have been made of materials in the disordered glassy state precluding the crystalline symmetry requirements necessary for piezoelectricity.Recent progress in drawing of fibres made of a multiplicity of materials 12 present new opportunities for re-examining this challenge. With this approach, fibre materials are drawn from 3 preforms in a regime dominated by viscous forces allowing for internal low viscosity domains to be arranged in non-equilibrium cross sections confined by viscous glassy boundary layers. In fact constructing a piezoelectric fibre could be accomplished in a straightforward manner by assembling a preform made of a piezoelectric material poly(vinylidene fluoride) (PVDF) 13-14 , with metal electrodes and an insulating polymer, which would be followed by a thermal draw.The stress present during the fibre draw should in principle induce the non-polar α to the ferroelectric β phase transition in the PVDF layer 13,[15][16] . The process should yield many metres of fibre with built-in internal electrodes which could be utilized to establish the large electric field necessary for poling the PVDF layer. However, upon detailed examination a number of significant challenges and seemingly conflicting requirements arise. The necessity to utilize crystalline materials both for the piezoelectric layer and the electrical conductors leads to the formation of multiple adjacent low viscosity and high aspect ratio domains. These domains undergoing a reduction in cross sectional dimensions are susceptible to capillary breakup and mixing during fibre drawing due to flow instabilities. Layer thickness non-uniformity either in the lateral or in the longitudinal directions [17][18] precludes the formation of the coercive field needed for poling. Moreover, even if capillary breakup were kinetically averted and uniform sections of fibres were to emerge they would not exhibit piezoelectricity because the stress and strain conditions necessary to induce the thermodynamic phase transition in PVDF cannot be sustained in the fibre draw process.To address these challenges we choose to focus our attention on the ability to maintain geometric coherence and layer thickness uniformity. A viscous and conductive carbon-loaded poly(carbonate) (CPC) is used to confine the low viscosity crystalline piezoelectric layer during 4 the draw process. The CPC layers exhibit high viscosity (10 5~1 0 6 Pa·s) at the draw temperature and adequate conductivity (1~10 4 ohm·m) over the frequency range from DC to tens of MHz, thus facilitating short range (hundreds of microns) charge transport on length scales associated with the fibre cross section. Then a piezoelectric polymer which crystallizes into the appropriate phase...

Ultrasound transducers have many important applications in medical, industrial, and environmental settings. Large-active-area piezoelectric fibers are presented here, which can be woven into extended and flexible ultrasound transducing fabrics. This work opens significant opportunities for large-area, flexible and adjustable acoustic emission and sensing for a variety of emerging applications.

Microelectromechanical systems (MEMS) enable many modern-day technologies, including actuators, motion sensors, drug delivery systems, projection displays, etc. Currently, MEMS fabrication techniques are primarily based on silicon micromachining processes, resulting in rigid and low aspect ratio structures. In this study, we report on the discovery of MEMS functionality in fibres, thereby opening a path towards flexible, high-aspect ratio, and textile MEMS. The method used for generating these MEMS fibres leverages a preform-to-fibre thermal drawing process, in which the MEMS architecture and materials are embedded into a preform and drawn into kilometers of microstructured multimaterial fibre devices. The fibre MEMS functionality is enabled by an electrostrictive P(VDF-TrFE-CFE) ferrorelaxor terpolymer layer running the entire length of the fibre. Several modes of operation are investigated, including thickness-mode actuation with over 8% strain at 25 MV m−1, bending-mode actuation due to asymmetric positioning of the electrostrictive layer, and resonant fibre vibration modes tunable under AC-driving conditions.

We report on the fabrication of all-in-fiber capacitors with poly(vinylidene fluoride) (PVDF) as the dielectric material. Electrodes made of conductive polymer are separated by a PVDF thin film within a polycarbonate casing that is thermally drawn into multiple meters of lightweight , readily functional fiber. Capacitive response up to 20 kHz is measured and losses at higher-frequencies are accounted for in a materials-based model. A multilayered architecture in which a folded PVDF film separates interdigitated electrodes over an increased area is fabricated. This structure greatly enhances the capacitance, which scales linearly with the fiber length and is unaffected by fiber dimension fluctuations. V

In the past decade, novel fiber structures and material compositions have led to the introduction of new diagnostic and therapeutic tools. We review the structure, the material composition and the fabrication processes behind these novel fiber systems. Because of their structural flexibility, their compatibility with endoscopic appliances and their efficiency in laser delivery, these fiber systems have greatly extended the reach of a wide range of surgical lasers in minimally invasive procedures. Much research in novel fiber-optics delivery systems has been focused on the accommodation of higher optical powers and the extension to a broader wavelength range. Until recently, CO2 laser surgery, renowned for its precision and efficiency, was limited to open surgeries by the lack of delivery fibers. Hollow-core photonic bandgap fibers are assessed for their ability to transmit CO2 laser at surgical power level and for their applications in a range of clinical areas. Current fiber-delivery technologies for a number of laser surgery modalities and wavelengths are compared.

Here we report on the design, fabrication, and characterization of fiber containing an internal crystalline non-centrosymmetric phase enabling piezoelectric functionality over extended fiber lengths [1]. A ferroelectric polymer layer of 30 m thickness is spatially confined and electrically contacted by internal viscous electrodes and encapsulated in an insulating polymer cladding hundreds of microns in diameter. The structure is thermally drawn in its entirety from a macroscopic preform, yielding tens of meters of piezoelectric fiber. Electric fields in excess of 50V/ m are applied through the internal electrodes to the ferroelectric layer leading to effective poling of the structure. To unequivocally establish that the internal copolymer layer is macroscopically poled we adopt a two-step approach. First, we show that the internal piezoelectric modulation indeed translates to a motion of the fiber's surface using a heterodyne optical vibrometer at kHz frequencies. Second, we proceed to an acoustic wave measurement at MHz frequencies: a water-immersion ultrasonic transducer is coupled to a fiber sample across a water tank, and frequency-domain characterizations are carried out using the fiber successively as an acoustic sensor and actuator. These measurements establish the broadband piezoelectric response and acoustic transduction capability of the fiber. The potential to modulate sophisticated optical devices is illustrated by constructing a single-fiber electricallydriven device containing a high-quality-factor Fabry-Perot optical resonator and a piezoelectric transducer.

No abstract

Ultrasound transducers have many important applications in medical, industrial, and environmental settings. , Yoel Fink and co‐workers report the realization of large‐active‐area piezoelectric fibers, which can be woven into extended and flexible ultrasound transducing fabrics. The back cover depicts a curved grid of piezoelectric fibers, four of which are actuated and emitting a focused acoustic wave.