No abstract

Data assimilation techniques were used to estimate forest stand data in 2011 by sequentially combining remote sensing based estimates of forest variables with predictions from growth models. Estimates of stand data, based on canopy height models obtained from image matching of digital aerial images at six different time-points between 2003 and 2011, served as input to the data assimilation. The assimilation routines were built on the extended Kalman filter. The study was conducted in hemi-boreal forest at the Remningstorp test site in southern Sweden (lat. 13˝37 1 N; long. 58˝28 1 E). The assimilation results were compared with two other methods used in practice for estimation of forest variables: the first was to use only the most recent estimate obtained from remotely sensed data (2011) and the second was to forecast the first estimate (2003) to the endpoint (2011). All three approaches were validated using nine 40 m radius validation plots, which were carefully measured in the field. The results showed that the data assimilation approach provided better results than the two alternative methods. Data assimilation of remote sensing time series has been used previously for calibrating forest ecosystem models, but, to our knowledge, this is the first study with real data where data assimilation has been used for estimating forest inventory data. The study constitutes a starting point for the development of a framework useful for sequentially utilizing all types of remote sensing data in order to provide precise and up-to-date estimates of forest stand parameters.

No abstract

Today, non-expensive remote sensing (RS) data from different sensors and platforms can be obtained at short intervals and be used for assessing several kinds of forest characteristics at the level of plots, stands and landscapes. Methods such as composite estimation and data assimilation can be used for combining the different sources of information to obtain up-to-date and precise estimates of the characteristics of interest. In composite estimation a standard procedure is to assign weights to the different individual estimates inversely proportional to their variance. However, in case the estimates are correlated, the correlations must be considered in assigning weights or otherwise a composite estimator may be inefficient and its variance be underestimated. In this study we assessed the correlation of plot level estimates of forest characteristics from different RS datasets, between assessments using the same type of sensor as well as across different sensors. The RS data evaluated were SPOT-5 multispectral data, 3D airborne laser scanning data, and TanDEM-X interferometric radar data. Studies were made for plot level mean diameter, mean height, and growing stock volume. All data were acquired from a test site dominated by coniferous forest in southern Sweden. We found that the correlation between plot level estimates based on the same type of RS data were positive and strong, whereas the correlations between estimates using different sources of RS data were not as strong, and weaker for mean height than for mean diameter and volume. The implications of such correlations in composite estimation are demonstrated and it is discussed how correlations may affect results from data assimilation procedures.

This study had the aim of investigating the utility of image-based point cloud data for estimation of vertical canopy cover (VCC). An accurate measure of VCC based on photogrammetric matching of aerial images would aid in vegetation mapping, especially in areas where aerial imagery is acquired regularly. The test area is located in southern Sweden and was divided into four vegetation types with sparse to dense tree cover: unmanaged coniferous forest; pasture areas with deciduous tree cover; wetland; and managed coniferous forest. Aerial imagery with a ground sample distance of 0.24 m was photogrammetrically matched to produce dense image-based point cloud data. Two different image matching software solutions were used and compared: MATCH-T DSM by Trimble and SURE by nFrames. The image-based point clouds were normalized using a digital terrain model derived from airborne laser scanner (ALS) data. The canopy cover metric vegetation ratio was derived from the image-based point clouds, as well as from raster-based canopy height models (CHMs) derived from the point clouds. Regression analysis was applied with vegetation ratio derived from near nadir ALS data as the dependent variable and metrics derived from image-based point cloud data as the independent variables. Among the different vegetation types, vegetation ratio derived from the image-based point cloud data generated by using MATCH-T resulted in relative root mean square errors (rRMSE) of VCC ranging from 6.1% to 29.3%. Vegetation ratio based on point clouds from SURE resulted in rRMSEs ranging from 7.3% to 37.9%. Use of the vegetation ratio based on CHMs generated from the image-based point clouds resulted in similar, yet slightly higher values of rRMSE. ARTICLE HISTORY

Accurate and up-to-date data about growing stock volume are essential for forest management planning. Airborne Laser Scanning (ALS) is known for producing accurate wall-to-wall predictions but the data are at present collected at long time intervals. Digital Photogrammetry (DP) is cheaper and often more frequently available but known to be less accurate. This study investigates the potential of using contemporary DP data together with older ALS data and compares this with the case when only old ALS data are trained with recent field data. Combining ALS data from 2010 to 2011 with DP data from 2015, both trained with National Forest Inventory (NFI) field plot data from 2015, improved predictions of growing stock volume. Validation using data from 100 stands inventoried in 2015 gave an RMSE of 24.3% utilizing both old ALS data and recent DP data, 26.0% for old ALS only and 24.9% for recent DP only. If information about management actions were assumed available, combining old ALS and recent DP gave RMSE of 23.0%, only ALS 23.3% and only DP 23.8%.

Today, non-expensive remote sensing (RS) data from different sensors and platforms can be obtained at short intervals and be used for assessing several kinds of forest characteristics at the level of plots, stands and landscapes. Methods such as composite estimation and data assimilation can be used for combining the different sources of information to obtain up-to-date and precise estimates of the characteristics of interest. In composite estimation a standard procedure is to assign weights to the different individual estimates inversely proportional to their variance. However, in case the estimates are correlated, the correlations must be considered in assigning weights or otherwise a composite estimator may be inefficient and its variance be underestimated. In this study we assessed the correlation of plot level estimates of forest characteristics from different RS datasets, between assessments using the same type of sensor as well as across different sensors. The RS data evaluated were SPOT-5 multispectral data, 3D airborne laser scanning data, and TanDEM-X interferometric radar data. Studies were made for plot level mean diameter, mean height, and growing stock volume. All data were acquired from a test site dominated by coniferous forest in southern Sweden. We found that the correlation between plot level estimates based on the same type of RS data were positive and strong, whereas the correlations between estimates using different sources of RS data were not as strong, and weaker for mean height than for mean diameter and volume. The implications of such correlations in composite estimation are demonstrated and it is discussed how correlations may affect results from data assimilation procedures.

A workflow for combining airborne lidar, optical satellite data and National Forest Inventory (NFI) plots for cost efficient operational mapping of a nationwide sample of 5 × 5 km squares in the National Inventory of Landscapes in Sweden (NILS) landscape inventory in Sweden is presented. Since the areas where both satellite data and lidar data have a common data quality are limited, and impose a constraint on the number of available NFI plots, it is not feasible to perform classifications in a single step. Instead a stratified approach where canopy cover and canopy height are first predicted from lidar data trained with NFI plots is proposed. From the lidar predictions a forest stratum is defined as grid cells with more than 3 m mean tree height and more than 10% vertical canopy cover, the remaining grid cells are defined as open land. Both forest and open land are then classified into broad vegetation classes using optical satellite data. The classification of open land is trained with aerial photo interpretation and the classification of the forest stratum is trained with a new set of NFI plots. The result is a rational procedure for nationwide sample based vegetation characterization.