Using a parallel-plate flow chamber, the hydrodynamic shear forces to prevent bacterial adhesion (F prev ) and to detach adhering bacteria (F det ) were evaluated for hydrophilic glass, hydrophobic, dimethyldichlorosilane (DDS)-coated glass and six different bacterial strains, in order to test the following three hypotheses. 1. A strong hydrodynamic shear force to prevent adhesion relates to a strong hydrodynamic shear force to detach an adhering organism. 2. A weak hydrodynamic shear force to detach adhering bacteria implies that more bacteria will be stimulated to detach by passing an air-liquid interface (an air bubble) through the flow chamber. 3. DLVO (Derjaguin, Landau, Verwey, Overbeek) interactions determine the characteristic hydrodynamic shear forces to prevent adhesion and to detach adhering micro-organisms as well as the detachment induced by a passing air-liquid interface. F prev varied from 0.03 to 0.70 pN, while F det varied from 0.31 to over 19.64 pN, suggesting that after initial contact, strengthening of the bond occurs. Generally, it was more difficult to detach bacteria from DDS-coated glass than from hydrophilic glass, which was confirmed by air bubble detachment studies. Calculated attractive forces based on the DLVO theory (F DLVO ) towards the secondary interaction minimum were higher on glass than on DDS-coated glass. In general, all three hypotheses had to be rejected, showing that it is important to distinguish between forces acting parallel (hydrodynamic shear) and perpendicular (DLVO, air-liquid interface passages) to the substratum surface.

Time-dependent bacterial adhesion forces of four strains of Staphylococcus epidermidis to hydrophobic and hydrophilic surfaces were investigated. Initial adhesion forces differed significantly between the two surfaces and hovered around -0.4 nN. No unambiguous effect of substratum surface hydrophobicity on initial adhesion forces for the four different S. epidermidis strains was observed. Over time, strengthening of the adhesion forces was virtually absent on hydrophobic dimethyldichlorosilane (DDS)-coated glass, although in a few cases multiple adhesion peaks developed in the retract curves. Bond-strengthening on hydrophilic glass occurred within 5-35 s to maximum adhesion forces of -1.9 +/- 0.7 nN and was concurrent with the development of multiple adhesion peaks upon retract. Poisson analysis of the multiple adhesion peaks allowed separation of contributions of hydrogen bonding from other nonspecific interaction forces and revealed a force contribution of -0.8 nN for hydrogen bonding and +0.3 nN for other nonspecific interaction forces. Time-dependent bacterial adhesion forces were comparable for all four staphylococcal strains. It is concluded that, on DDS-coated glass, the hydrophobic effect causes instantaneous adhesion, while strengthening of the bonds on hydrophilic glass is dominated by noninstantaneous hydrogen bond formation.

No abstract

Adhesion and residence-time-dependent desorption of two Staphylococcus aureus strains with and without fibronectin (Fn) binding proteins (FnBPs) on Fn-coated glass were compared under flow conditions. To obtain a better understanding of the role of Fn-FnBP binding, the adsorption enthalpies of Fn with staphylococcal cell surfaces were determined using isothermal titration calorimetry (ITC). Interaction forces between staphylococci and Fn coatings were measured using atomic force microscopy (AFM). The strain with FnBPs adhered faster and initially stronger to an Fn coating than the strain without FnBPs, and its Fn adsorption enthalpies were higher. The initial desorption was high for both strains but decreased substantially within 2 s. These time scales of staphylococcal bond ageing were confirmed by AFM adhesion force measurement. After exposure of either Fn coating or staphylococcal cell surfaces to bovine serum albumin (BSA), the adhesion of both strains to Fn coatings was reduced, suggesting that BSA suppresses not only nonspecific but also specific Fn-FnBP interactions. Adhesion forces and adsorption enthalpies were only slightly affected by BSA adsorption. This implies that under the mild contact conditions of convective diffusion in a flow chamber, adsorbed BSA prevents specific interactions but does allow forced Fn-FnBP binding during AFM or stirring in ITC. The bond strength energies calculated from retraction force-distance curves from AFM were orders of magnitude higher than those calculated from desorption data, confirming that a penetrating Fn-coated AFM tip probes multiple adhesins in the outermost cell surface that remain hidden during mild landing of an organism on an Fn-coated substratum, like that during convective diffusional flow.Staphylococcus aureus is a versatile pathogen which can adhere to epithelial cells, endothelial cells, and fibroblasts, as well as to plasma-exposed biomaterial implant surfaces in the human body (12), causing potentially persistent infections. The best-described mechanism of S. aureus adhesion to eukaryotic cells and other fibronectin ( At constant temperature and pressure, bacterial adhesion to surfaces is accompanied by a decrease in the Gibbs energy (⌬G). ⌬G is composed of a change in enthalpy (⌬H) and a change in entropy (⌬S) according to the following equation:where T is the temperature (in Kelvin). The enthalpy tends to reach a minimum value, whereas the entropy strives for a maximum value. The change in enthalpy can be determined by determining the heat exchange between a system and its environment, while direct determination of the entropy is practically impossible. Many biological processes are characterized by strong enthalpy-entropy compensation (10); that is, they occur spontaneously by virtue of an increase in entropy that compensates for an unfavorable enthalpy effect or vice versa. The enthalpy of the interaction between bacterial cell surfaces and proteins can be assessed using isothermal titration calorimetry (ITC). Xu et al. (28) determined the adso...

No abstract

No abstract

Poly (D,L-lactide)-7co-(1,3-trimethylene carbonate) [P(DLLA-co-TMC)] (83 mol % DLLA) was used to produce matrices suitable for tissue engineering of small-diameter blood vessels. The copolymer was processed into tubular structures with a porosity of approximately 98% by melt spinning and fiber winding, thus obviating the need of organic solvents that may compromise subsequent cell culture. Unexpectedly, incubation in culture medium at 37 degrees C resulted in disconnection of the contact points between the polymer fibers. To improve the structural stability of these P(DLLA-co-TMC) scaffolds, a collagen microsponge was formed inside the pores of the synthetic matrix by dip coating and freeze drying. Hybrid structures with a porosity of 97% and an average pore size of 102 mum were obtained. Structural stability was preserved during incubation in culture medium at 37 degrees C. Smooth-muscle cells (SMCs) were seeded in these hybrid scaffolds and cultured under pulsatile flow conditions in a bioreactor (120 beats/min, 80-120 mmHg). After 7 days of culture in a dynamic environment viable SMCs were homogeneously distributed throughout the constructs, which were five times stronger and stiffer than noncultured scaffolds. Values for yield stress (2.8 +/- 0.6 MPa), stiffness (1.6 +/- 0.4 MPa), and yield strain (120% +/- 20%) were comparable to those of the human artery mesenterica.