The use of bio-based material for repairing concrete is a relatively new method. Therefore, more results from simulated real-condition experiments are needed before being applied on a practical scale. In the recent past, several studies have been conducted on the improvement of bio-based repair materials. In this study, the bio-based material involving yeast, glucose, and calcium acetate mixed in a Tris buffer solution showed the potential to develop a microbial process leading to the precipitation of calcium carbonate. We investigated the factors affecting the precipitation rate of the calcium carbonate of bio-based materials for repairing leakage in the concrete specimens. Based on a series of experiments involving temperature, the type of dry yeast, and the concentration of the Tris buffer solution, the composition of bio-based materials with the highest precipitation rate of calcium carbonate was selected. The selected mixture could be applied to repair leakage of concrete until the cracks are sealed entirely.
The development of computational technology has provided convenience in structural planning to calculate earthquake loads acting on structures. This study aims to compare the results of the equivalent static earthquake load calculation using the existing methods in SAP 2000, with manual calculations based on SNI 1726 2019. This study will compare the base shear and story shear in a five-story building with a symmetrical building configuration and located in the city of Padang. The results of the comparison of the base shear using the SNI 2716 2019 method and the user load method produced the same value, namely 2441,707 kN, while the user coefficient method and the ASCE 7-16 method had a difference of 2.02% and 2.11% base shear values. For story shear calculations, the SNI 1726 2019 method with the user load method produces almost the same value with a difference of 0.002 to 0.004%. However, for story shear, the user coefficient method and ASCE 7-16 provide differences for the 5th floor, namely 7.25 and 5.94%, while for the 1st floor to the 4th floor the difference is only 3.67% to 2.70%.
Perubahan area lahan pertanian dan area resapan air sebagai penopang kebutuhan air untuk pertanian dibutuhkan solusi aplikatif dan singkat untuk masyarakat dan petani. Hal ini bisa dilakukan dengan memanfaatkan tingginya curah hujan yang ada di daerah Sumatera Barat. Data 2018 dari BPS menunjukkan banyaknya curah hujan per bulan mulai dari 50 – 1000 mm3 yang menandakan bahwa air hujan sebenarnya bisa dimanfaatkan sebagai alternatif untuk pemenuhan kebutuhan sumber air bagi penopang pertanian. Masalah utama adalah perubahan fungsi lahan yang semula diperuntukkan untuk resapan air hujan menjadi fungsi lain sehingga menjadikan ketersedian air tanah menjadi bekurang. Disamping itu masalah lain yang timbul dikarenakan tingginya tingkat kebutuhan air untuk keperluan sosial dan pertanian ketika terjadi musim kemarau. Untuk itu diperlukan teknologi sederhana untuk menahan dan menyimpan air hujan untuk jangka pendek dan menengah. Kemudian air tersebut dialirkan ke dalam shaft buatan berupa saluran parit yang kemudian dikumpulkan ke dalam reservoar komunal sebagai cadangan sehingga bisa dimanfaatkan untuk sektor pertanian dan rumah tangga. Kegiatan Pengabdian Masyarakat ini dilaksanakan di Kenagarian Aia Gadang Kabupaten Pasaman Barat yang merupakan daerah bercurah hujan tinggi dan sedang dengan neraca air defisit, run off tinggi dan vegetasi penutup tanah yang kurang dari 30%. Pelaksanaan kegiatan pengabdian masyarakat diawali dengan tahapan persiapan pada daerah permukiman padat penduduk. Kemudian dilanjutkan dengan tahapan sosialisasi serta pemberian dokumen pendukung dan desain teknis persiapan pra-kontruksi. Peserta pelatihan sangat antusias terhadap penyampaian materi pelatihan karena menambah ilmu mereka yang sebagian besar berlatar pendidikan rendah dan tidak ditunjang oleh adanya pendidikan keilmuan di bidang Teknik Sipil dan Lingkungan. Hasil evaluasi menunjukkan rata-rata peningkatan pengetahuan tentang sumur resapan meningkat. Dengan demikian peserta memiliki pengetahuan tentang teknologi sederhana yang dapat diterapkan pada kegiatan pembuatan sumur resapan.
Indonesia merupakan wilayah yang berada pertemuan tiga lempeng aktif yaitu, lempeng Indo-Australia, Eurasia, dan Pasifik dan juga berada pada jalur cincin api atau ring of fire, menyebabkan sering terjadinya gempa bumi di Indonesia. Dalam perencanaan bangunan seperti Sistem Rangka Pemikul Khusus (SRPMK) yang merupakan bagian dari Sistem Rangka Pemikul Momen (SRPM) yang memang digunakan pada wilayah dengan resiko tinggi terhadap gempa bumi. Proses perancangan suatu bangunan gedung maupun non gedung menggunkan aplikasi penunjang Teknik Sipil seperti, untuk menganalisis struktur bangunan menggunakan aplikasi SAP 2000 atau ETABS. Adapun tujuan dari tugas akhir ini adalah membuat sebuah aplikasi komputer untuk perhitungan kebutuhan baja tulangan untuk menahan momen lentur pada SRPMK dengan menggunakan bahasa pemrograman Visual Basic.Net versi 2013.Berdasarkan hasil validasi yang dilakukan terhadapap pruduk berupa aplikasi DSB SRPMK didapatkan dari rumus validitas percentages correction nilai persentase dari ahli materi sebesar 80% dengan kategori kelayakan ‘Baik’ dan untuk ahli media didapatkan nilai persentase sebesar 93.4% dengan kategori kelayakan ‘Sangat Baik’. Sedangkan dari hasil perbandingan ketiga software yang digunakan untuk pembanding hasil perhitungan kebutuhan baja tulangan pada elemen stuktur balok SRPMK dengan menggunakan aplikasi SAP 2000, Microsoft Excel, dan aplikasi DSB SRPMK, didapatkan nilai persentase sebesar 95% dengan kategori kelayakan ‘Sangat Baik’.
Chloride-induced corrosion of steel bar in concrete is one of the main problems affecting the durability of reinforced concrete (RC) structures. Expansive products are formed due to corrosion at the interface between concrete and steel bar. In this study, the differences in the magnitude of the macrocell corrosion current density in RC column specimens cast using copper slag fine aggregate and fly ash replacement were examined. This study aimed at investigating corrosion formation with respect to macrocell corrosion current density. The experimental study was carried out through dry and wet (NaCl 10%) cycles for specimens with different cover depths, which was investigated by electrochemical measurements. The result shows that the largest macrocell corrosion current density was measured in the steel bars located at the upper part of reinforced column specimens for each case of the specimens with a cover depth of 30 mm. This could be partly attributed to the loss of the integrity of the steel and concrete interface which is examined based on the oxygen permeability in the upper and lower sides of segmented steel bars. The variation of oxygen permeability contributes to the macrocell corrosion formation especially in the steel bars affected by bleeding water. Besides the integrity between steel bars and concrete cover, the quality of concrete cover and variations in chloride ion concentrations are significant factors contributing to the macrocell corrosion formation.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.