Thermal modification is the most important commercial modification procedure. Thermally modified (TM) wood has improved durability, but its performance does not meet expectations predominately under moist conditions. To reduce water uptake of TM wood, Norway spruce specimens were treated with suspensions of a natural wax by dipping impregnation (DipI) or by vacuum-pressure impregnation (VPI). Wax-treated specimens were subsequently TM at 185, 200, 215, and 230°C. Control specimens were heated up to 100°C only. Contact angle (CA), short-term and long-term water uptake, bending strength, and performance against wood decay fungi of the resulting material were determined. The results show that a combination of wax treatment and thermal modification have a synergistic effect that considerably improves hydrophobicity, reduces liquid water uptake, slows down water vapor uptake, and improves the resistance against fungal decay of the treated material.

The importance of the aesthetic performance of wood is increasing and the colour is one of the most important parameters of aesthetics, hence the colour stability of twelve different wood-based materials was evaluated by several in-service and laboratory tests. The wood used for wooden façades and decking belongs to a group of severely exposed surfaces. Discolouration of wood in such applications is a long-known phenomenon, which is a result of different biotic and abiotic causes. The ongoing in-service trial started in October 2013, whilst a laboratory test mimicking seasonal exposure was performed in parallel. Samples were exposed to blue stain fungi (Aureobasidium pullulans and Dothichiza pithyophila) in a laboratory test according to the EN 152 procedure. Afterwards, the same samples were artificially weathered and re-exposed to the same blue stain fungi for the second time. The purpose of this experiment was to investigate the synergistic effect of weathering and staining. The broader aim of the study was to determine the correlation factors between artificial and natural weathering and to compare laboratory and field test data of fungal disfigurement of various bio-based materials. During the four years of exposure, the most prominent colour changes were determined on decking. Respective changes on the façade elements were significantly less prominent, being the lest evident on the south and east façade. The results showed that there are positive correlations between natural weathering and the combination of artificial weathering and blue staining. Hence, the artificial weathering of wood-based materials in the laboratory should consist of two steps, blue staining and artificial weathering, in order to simulate colour changes.

Despite increased interest in the timing and dynamics of phloem formation, seasonal changes in the structure of phloem sieve elements remain largely unexplored. To understand better the dynamics of phloem formation and the functioning of sieve tubes in the youngest phloem in Fagus sylvatica L., we investigated repeatedly taken phloem samples during the growing season of 2017 by means of light microscopy, and transmission and scanning electron microscopy. Phloem formation started with the expansion of the overwintered early phloem sieve tubes adjacent to the cambium and concurrent cambial cell production. The highest phloem growth rate was observed in general 1 week after the onset of cambial cell production, whereas the transition from early to late phloem occurred at the end of May. Cambial cell production ceased at the end of July. The final width of the phloem increment was 184 ± 10 μm, with an early phloem proportion of 59%. Collapse of older phloem tissue is a progressive process, which continuously occurred during the sampling period. Collapse of early phloem sieve tubes started shortly after the cessation of cambial cell production. Prior to the onset of radial growth, late phloem from the previous year represented 80% of the total non-collapsed part; during the growth period, this percentage decreased to 20%. Differences were observed in both sieve tube ultrastructure and sieve plate geometry between the youngest and older phloem. However, sieve plates were never completely occluded by callose, suggesting that processes affecting the functionality of sieve tubes may differ in the case of regular collapse or injury. The youngest parts of the phloem increment from the previous year (i.e., previous late phloem) continue functioning for some time in the current growing season, but the two-step development of overwintered phloem cells also ensures a sufficient translocation pathway for photosynthates to the actively growing tissues.

No abstract

No abstract

No abstract

No abstract

No abstract