ABSTRACT:Composites of natural rubber (NR) and short pineapple leaf fiber (PALF) were prepared on a laboratory two-roll mill. The influences of untreated fiber content and orientation on the processing and mechanical properties of the composites were investigated. The dependence of extent of orientation on fiber concentration was also established. Sodium hydroxide (NaOH) solutions (1, 3, 5, and 7% w/v) and benzoyl peroxide (BPO) (1, 3, and 5 wt % of fiber) were used to treat the surfaces of PALFs. FTIR and scanning electron microscope (SEM) observations were made of the treatments in terms of chemical composition and surface structure. The tensile strength and elongation at break of the composites were later studied. The fiber-matrix adhesion was also investigated using SEM technique. It was found that all surface modifications enhanced adhesion and tensile properties. The treatments with 5% NaOH and 1% BPO provided the best improvement of composite strength (28 and 57% respectively) when compared with that of untreated fiber. The PALF-NR composites also exhibited better resistance to aging than its gum vulcanizate, especially when combined with the treated fibers.

Three kinds of surface treatment, that is, the alkalization (5% w/v NaOH aqueous solution), the deposition of diglycidyl ether of bisphenol A (DGEBA) from toluene solution (1% w/v DGEBA), and the alkalization combined with the deposition of DGEBA (5% w/v NaOH/1% w/v DGEBA) were applied to modify interfacial bonding and to enhance mechanical properties of pineapple leaf fiber (PALF) reinforced epoxy composites. The fiber strength and strain were measured by single fiber test and the fiber strength variation was assessed using Weibull modulus. Furthermore, a fragmentation test was used to quantify the interfacial adhesion of PALFepoxy composite. It was verified that the interfacial shear strength of modified PALFs was substantially higher than that of untreated PALF by almost 2-2.7 times because of the greater interaction between the PALFs and epoxy resin matrix. The strongest interfacial adhesion was obtained from the fibers that had been received the alkalization combined with DGEBA deposition. Moreover, the flexural and impact properties of unidirectional PALF-epoxy composites were greatly enhanced when reinforced with the modified PALFs due to an improvement in interfacial adhesion, particularly in the synergetic use of 5% NaOH and 5% NaOH/1% DGEBA.

No abstract

No abstract

Nanocomposites of natural rubber (NR) and unmodified clay were prepared by latex compounding method. Phenolic resin (PhOH) was used to crosslink NR. Crosslinked neat NR was also prepared for comparison. The structure–property relationship of uncrosslinked and crosslinked NR/clay nanocomposites was examined to verify the reinforcement mechanism. Microstructure of NR/clay nanocomposites was studied by using transmission electron microscopic (TEM), X‐ray diffraction (XRD), wide angle X‐ray diffraction (WAXD), and small angle X‐ray scattering (SAXS) analyses. The results showed the evidence of intercalated clay together with clay tactoids for the nanocomposite samples. The highest tensile strength was achieved for the crosslinked NR/clay nanocomposite. The onset strain of deformation induced the crystallization of NR for nanocomposites was found at almost the same strain, and furthermore their crystallization was developed at lower strain than that of the crosslinked neat NR because of the clay orientation and alignment. However, at high strain region, the collaborative crystallization process related to the clay dispersion and conventional crosslink points in the NR was responsible to considerably high tensile strength of the crosslinked NR/clay nanocomposite. Based on these analyses, a mechanistic model for the strain‐induced crystallization and orientational evolution of a network structure of PhOH‐crosslinked NR/clay nanocomposite was proposed. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015, 132, 42580.

Natural-rubber-based hybrid composites were prepared by the mixture of short cellulose fibers and silica of different relative contents with a 20-phr filler loading with a laboratory two-roll mill. The processability and tensile properties of the hybrid composites were analyzed. The tensile modulus improved, but the tensile strength and elongation at break decreased with increasing cellulose fiber content. The scorch safety improved with the addition of 5-phr cellulose fiber in the composites. The Mooney viscosity significantly decreased with increasing cellulose fiber content. To modify the surface properties of the cellulose fiber and silica fillers, a silane coupling agent [bis(triethoxysilylpropyl)tetrasulfide, or Si69] was used. The effects of Si69 treatment on the processing and tensile properties of the hybrid composites were assessed. We found that the silane treatment of both fillers had significant benefits on the processability but little benefit on the rubber reinforcement. The strength of the treated hybrid composite was comparable to that of silica-reinforced natural rubber. Furthermore, to investigate the filler surface modification and to determine the mixing effects, infrared spectroscopic and various microscopic techniques, respectively, were used. From these results, we concluded that the fillers were better dispersed in the composites, and the compatibility of the fillers and natural rubber increased with silane treatment. In conclusion, the hybridized use of short cellulose fibers from a renewable resource and silica with Si69 presented in this article offers practical benefits for the production of rubber-based composites having greater processability and more environmental compatibility than conventional silica-filler-reinforced rubber.

Nanocomposites of natural rubber (NR) and pristine clay (clay) were prepared by latex mixing, then crosslinked with phenolic resin (PhOH). For comparative study, the PhOH‐crosslinked neat NR was also prepared. Influence of clay loading (i.e., 1, 3, 5, and 10 phr) on mechanical properties and structural change of PhOH‐crosslinked NR/clay nanocomposites was studied through X‐ray diffraction (XRD), transmission electron microscopic (TEM), wide‐angle X‐ray diffraction (WAXD), tensile property measurement, and Fourier transform infrared spectroscopy (FTIR). XRD and TEM showed that the clay was partly intercalated and aggregated, and that the dispersion state of clay was non‐uniform at higher clay loading (>5 phr). From tensile test measurement, it was found that the pronounced upturn of tensile stress was observed when the clay loading was increased and a maximum tensile strength of the PhOH‐crosslinked NR/clay nanocomposites was obtained at 5 phr clay. WAXD observations showed that an increased addition of clay induced more orientation and alignment of NR chains, thereby lowering onset strain of strain‐induced crystallization and promoting crystallinity of the NR matrix during tensile deformation. FTIR investigation indicated a strong interfacial adhesion between NR matrix and clay filler through a phenolic resin bridge. This suggested that the PhOH did not only act as curative agent for crosslinking of NR, but it also worked as coupling agent for promoting interfacial reaction between NR and clay. The presence of strong interfacial adhesion was found to play an important role in the crystallization process, leading to promotion of mechanical properties of the PhOH‐crosslinked NR/clay nanocomposites. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016, 133, 43214.

Nanocomposite foams were fabricated from 60/40 wt% ethylene vinyl acetate (EVA)/natural rubber (NR) blends by using azodicarbonamide as a blowing agent. Two different nanofillers (sodium montmorillonite and organoclay) were employed to study their effects on foam properties. The results were also compared with conventional (china clay)‐filled foams. Transmission electron microscopy, X‐ray diffraction, scanning electron microscopy, and three‐dimensional Microfocus X‐ray computed tomography scanning analysis were performed to characterize the EVA/NR blend morphology and foam structures. The results revealed that the nanofiller acted as a blend compatibilizer. Sodium montmorillonite was more effective in compatibilization, generating better phase‐separated EVA/NR blend morphology and improving foam structure. Higher filler loading increased the specific tensile strength of rubber foams. The rubber nanocomposite foam showed superior specific tensile strength to the conventional rubber composite foam. The elastic recovery and compressive strength of the nanocomposite foams decreased with increasing filler content, whereas the opposite trend was observed for the conventional composite foams with china clay. The thermal conductivity measurement indicated that the nanofiller had better beneficial effect on thermal insulation over china clay filler. From the present study, the nanofillers played an important role in obtaining better blend morphology as compatibilizer, rather than the nucleating agent and the nanofiller content of 5 phr (parts by weight per hundred parts of rubber) was recommended for the production of EVA/NR nanocomposite foams. J. VINYL ADDIT. TECHNOL., 21:134–146, 2015. © 2014 Society of Plastics Engineers