The aim of the presented study was preparation, analysis of properties, and in vitro characterization of porous shape-memory scaffolds, designed for large bone defects treatment using minimally invasive surgery approach. Biodegradable terpolymers of l-lactide/glycolide/trimethylene carbonate (LA/GL/TMC) and l-lactide/glycolide/ε-caprolactone (LA/GL/Cap) were selected for formulation of these scaffolds. Basic parameters of shape memory behavior (i.e. recovery ratio, recovery time) and changes in morphology (SEM, average porosity) and properties (surface topography, water contact angle, compressive strength) during shape memory cycle were characterized. The scaffolds preserved good mechanical properties (compressive strength about 0.7 to 0.9 MPa) and high porosity (more than 80%) both in initial shape as well as after return from compressed shape. Then the scaffolds in temporary shape were inserted into the model defect of bone tissue at 37°C. After 12 min the defect was filled completely as a result of shape recovery process induced by body temperature. The scaffold obtained from LA/GL/TMC terpolymer was found the most prospective for the planned application thanks to its appropriate recovery time, high recovery ratio (more than 90%), and cytocompatibility in contact with human osteoblasts and chondrocytes.

The paper presents the course of synthesis and properties of a series of block copolymers intended for biomedical applications, mainly as a material for forming scaffolds for tissue engineering. These materials were obtained in the polymerization of l-lactide and copolymerization of l-lactide with glycolide carried out using a number of macroinitiators previously obtained in the reaction of polytransesterification of succinic diester, citric triester and 1,4-butanediol. NMR, FTIR and DSC were used to characterize the materials obtained; wettability and surface free energy were assessed too. Moreover, biological tests, i.e., viability and metabolic activity of MG-63 osteoblast-like cells in contact with synthesized polymers were performed. Properties of obtained block copolymers were controlled by the composition of the polymerization mixture and by the composition of the macroinitiator. The copolymers contained active side hydroxyl groups derived from citrate units present in the polymer chain. During the polymerization of l-lactide in the presence of polyesters with butylene citrate units in the chain, obtained products of the reaction held a fraction of highly branched copolymers with ultrahigh molecular weight. The reason for this observed phenomenon was strong intermolecular transesterification directed to lactidyl side chains, formed as a result of chain growth on hydroxyl groups related to the quaternary carbons of the citrate units. Based on the physicochemical properties and results of biological tests it was found that the most promising materials for scaffolds formation were poly(l-lactide–co–glycolide)–block–poly(butylene succinate–co–butylene citrate)s, especially those copolymers containing more than 60 mol % of lactidyl units.

The aim of the study was the evaluation of gamma irradiation and electron beams for sterilization of porous scaffolds with shape memory behavior obtained from biodegradable terpolymers: poly(l-lactide-co-glycolide-co-trimethylene carbonate) and poly(l-lactide-co-glycolide-co-ɛ-caprolactone). The impact of mentioned sterilization techniques on the structure of the scaffolds before and after the sterilization process using irradiation doses ranged from 10 to 25 kGy has been investigated. Treatment of the samples with gamma irradiation at 15 kGy dose resulted in considerable drop in glass transition temperature (Tg) and number average molecular weight (Mn). For comparison, after irradiation of the samples using an electron beam with the same dose, no significant changes in structure or properties of examined scaffolds have been noticed. Higher doses of irradiation via electron beam caused essential changes of the scaffolds’ pores resulting in partial melting of their surface. Nevertheless, obtained results have revealed that sterilization with electron beam, when compared to gamma irradiation, is a better method because it does not affect significantly the physicochemical properties of the scaffolds. Both used methods of sterilization did not influence the shape memory behavior of the examined materials.

The paper presents the formation and properties of biodegradable thermoplastic blends with triple-shape memory behavior, which were obtained by the blending and extrusion of poly(l-lactide-co-glycolide) and bioresorbable aliphatic oligoesters with side hydroxyl groups: oligo (butylene succinate-co-butylene citrate) and oligo(butylene citrate). Addition of the oligoesters to poly (l-lactide-co-glycolide) reduces the glass transition temperature (Tg) and also increases the flexibility and shape memory behavior of the final blends. Among the tested blends, materials containing less than 20 wt % of oligo (butylene succinate-co-butylene citrate) seem especially promising for biomedical applications as materials for manufacturing bioresorbable implants with high flexibility and relatively good mechanical properties. These blends show compatibility, exhibiting one glass transition temperature and macroscopically uniform physical properties.

The article presents the results of the synthesis and characteristics of the amphiphilic block terpolymers, built of a hydrophilic polyesteramine block, and hydrophobic blocks made of lactidyl and glycolidyl units. These terpolymers were obtained during the copolymerization of L-lactide with glycolide carried out in the presence of previously produced macroinitiators with protected amine and hydroxyl groups. The terpolymers were prepared to produce a biodegradable and biocompatible material containing active hydroxyl and/or amino groups, with strong antibacterial properties and high surface wettability by water. The control of the reaction course, the process of deprotection of functional groups, and the properties of the obtained terpolymers were made based on 1H NMR, FTIR, GPC, and DSC tests. Terpolymers differed in the content of amino and hydroxyl groups. The values of average molecular mass oscillated from about 5000 g/mol to less than 15,000 g/mol. Depending on the length of the hydrophilic block and its composition, the value of the contact angle ranged from 50° to 20°. The terpolymers containing amino groups, capable of forming strong intra- and intermolecular bonds, show a high degree of crystallinity. The endotherm responsible for the melting of L-lactidyl semicrystalline regions appeared in the range from about 90 °C to close to 170 °C, with a heat of fusion from about 15 J/mol to over 60 J/mol.