ResumoObjetivo: Caracterizar os pacientes atendidos e os procedimentos realizados no Serviço de Atendimento a Pacientes com Necessidades Especiais da Faculdade de Odontologia de Araraquara (FOAr) -UNESP. Metodologia: A partir dos prontuários odontológicos dos pacientes atendidos em nível ambulatorial entre 2007 e 2013, foram obtidas informações em relação a idade no início do tratamento, tipo de deficiência, medicamentos usados, número de sessões de atendimento e número e tipo de procedimentos odontológicos realizados. Resultado: Dos 232 prontuários analisados, observou-se que mais da metade dos pacientes (56,0%) apresentava deficiência mental, paralisia cerebral ou anomalias congênitas determinadas por agentes infecciosos, com deficiência mental associada. Entre as anomalias congênitas, a mais prevalente foi a Síndrome de Down (9,9%). Apenas 20% dos pacientes iniciaram o tratamento antes dos dez anos de idade e 62,0% faziam uso de anticonvulsivantes, antipsicóticos, ansiolíticos, antiepilépticos e antidepressivos. Foram realizados 4.506 procedimentos odontológicos, sendo 37,6% preventivos e 62,4% curativos (Restauradores, 28,0%; Periodontais, 13,9%; Endodônticos, 9,7%; Cirúrgicos, 9,1%; Protéticos, 1,7%). Observou-se também que, para a maior parte dos pacientes (63%), foram necessárias até dez sessões para a realização do tratamento. Conclusão: Os pacientes que procuraram tratamento odontológico no Serviço de Atendimento a Pacientes com Necessidades Especiais da FOAr apresentavam, na sua maioria, deficiências com envolvimento neurológico. Apesar de esse serviço priorizar os procedimentos preventivos, a maior parte dos procedimentos executados foi curativa, o que está diretamente relacionado com a procura tardia pelo tratamento odontológico.Descritores: Pessoas com deficiência; assistência odontológica para pessoas com deficiências; uso de medicamentos. AbstractObjective: To characterize the patients and dental procedures performed in Service to Patients with Special Needs of Araraquara School of Dentistry (FOAr) -UNESP. Methodology: From the dental records of patients treated at outpatient basis between 2007 and 2013, information regarding age at the beginning of treatment, type of disability, controlled medications used, number of dental sessions, and number and type of dental procedures performed was obtained. Result: Of the 232 records analyzed, more than half of the patients (56.0%) had mental retardation, cerebral palsy or congenital abnormalities caused by infectious agents associated with mental retardation. Among the congenital abnormalities, the most prevalent was the Down syndrome (9.9%). Only 20% of patients started treatment before the age of ten and 62.0% used anticonvulsants, antipsychotics, anxiolytics, antidepressants and antiepileptics. A total of 4,506 dental procedures were performed, 37.6% were preventive procedures and 62.4% curative procedures (restorative, 28.0%; periodontal, 13.9%; endodontic, 9.7%; surgical, 9.1%, and prosthetic 1.7%). Also was observed that for most patients (63%) up t...

Reduced salivary flow rate might be an important factor in oral diseases development. High salivary levels of SOD and MDA show the significant influence of the oxidative stress and the early-onset periodontal disease in DS people.

Aim: To study influence of the cooling rate after sintering a veneering porcelain (Vita VM9) on fracture toughness by indentation strength (IS) and single-edge-v-notched beam (SEVNB) methods. Methods: Vita VM9 bars were sintered according to the manufacturer’s recommendation and cooled under three conditions: Slow (inside the furnace from sintering temperature to room temperature); Normal (inside the furnace from sintering temperature to 500 ºC and outside the furnace from 500 ºC to room temperature); and Fast (outside the furnace from sintering temperature to room temperature). Fracture toughness was measured by IS (n=10) and SEVNB (n=10) methods. Data were analyzed by two-way ANOVA (α=0.05). Results: The fracture toughness obtained from SEVNB (slow - 1.02±0.10; normal - 1.09±0.13; and fast - 1,02±0.18 MPa.m1/2 cooling techniques) was significantly lower than IS (slow - 1.19±0.13; normal - 1.17±0.07; and fast - 1.16±0.06 MPa. m1/2 cooling techniques). There was no significant influence of the cooling technique (p=0.012). Conclusions: The measurement technique influenced the fracture toughness values . IS method overestimated the fracture toughness values. Irrespective of the measuring method, cooling rate did not influence the Vita VM9 veneering porcelain fracture toughness.

Slow cooling seems to affect the veneer resistance and adhesion to the zirconia core; however, the reliability of fast cooling was slightly lower than that of the other methods.