Aim: To study influence of the cooling rate after sintering a veneering porcelain (Vita VM9) on fracture toughness by indentation strength (IS) and single-edge-v-notched beam (SEVNB) methods. Methods: Vita VM9 bars were sintered according to the manufacturer’s recommendation and cooled under three conditions: Slow (inside the furnace from sintering temperature to room temperature); Normal (inside the furnace from sintering temperature to 500 ºC and outside the furnace from 500 ºC to room temperature); and Fast (outside the furnace from sintering temperature to room temperature). Fracture toughness was measured by IS (n=10) and SEVNB (n=10) methods. Data were analyzed by two-way ANOVA (α=0.05). Results: The fracture toughness obtained from SEVNB (slow - 1.02±0.10; normal - 1.09±0.13; and fast - 1,02±0.18 MPa.m1/2 cooling techniques) was significantly lower than IS (slow - 1.19±0.13; normal - 1.17±0.07; and fast - 1.16±0.06 MPa. m1/2 cooling techniques). There was no significant influence of the cooling technique (p=0.012). Conclusions: The measurement technique influenced the fracture toughness values . IS method overestimated the fracture toughness values. Irrespective of the measuring method, cooling rate did not influence the Vita VM9 veneering porcelain fracture toughness.
ResumoO objetivo deste trabalho é apresentar uma máquina para entalhamento de corpos de prova cerâmicos, bem como a escolha e a execução do entalhamento, usando SiC sinterizado via fase líquida, com adições de Al 2 O 3 e Yb 2 O 3 , como material experimental para ser entalhado. Foi desenvolvido e construído, junto a uma empresa de S. Carlos-SP, um equipamento que permite produzir entalhes finos em corpos cerâmicos para posterior ruptura, visando determinar K IC pelo método SEVNB. Amostras de SiC com 10% de Al 2 O 3 +Yb 2 O 3 foram sinterizadas a 1950 ºC, retificadas e entalhadas com lâminas de barbear e pastas diamantadas de 15, 9, 6, 3, 1 e 0,25 mm. A máquina produzida para o entalhamento das amostras está em operação no DEMAR-EEL-USP e, ao que se sabe, é a primeira no Brasil. Os resultados mostraram que em função da espessura da lâmina e da granulometria do agente abrasivo, pode-se produzir entalhes com diferentes raios de curvatura de sua ponta e profundidades. Palavras-chave: tenacidade à fratura, SEVNB, entalhamento, SiC.
Abstract
The aim of this work is to present a machine to produce notches in ceramic bodies
ResumoO concreto de cimento Portland é um dos materiais mais usados no mundo inteiro, entretanto, devido a sua estrutura ser muito complexa, torna-se imprescindível estudar suas propriedades com bastante profundidade. O concreto é produzido a partir de uma argamassa, de areia e cimento, com adição de agregados graúdos, sendo que suas propriedades estão basicamente suportadas nessa argamassa de constituição. O objetivo deste trabalho foi estudar a variação da rigidez de duas argamassas de composições com razão cimento:areia de 1:2 e 1:3 em função do tempo de cura, tendo como parâmetro a variação do módulo de Young. Os resultados mostraram que o módulo de Young cresce até atingir o valor máximo no oitavo dia, sendo que nos três primeiros dias esse crescimento é mais acentuado. A análise dos resultados indica que grande parte do processo de hidratação do cimento, com formação das ligações químicas responsáveis pela rigidez da argamassa, acontece nos primeiros dias de cura. Palavras-chave: Cimento Portland, argamassa, concreto, cura, módulo de Young.
Abstract
Concrete produced with
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.