No abstract

Prussian Blue Analogue (PBA)-Zn aqueous batteries are attractive because of the high potential of PBA against Zn (~1.7 V), relative safety of the system, and high rate capability. But, despite the long cycle life of PBA half-cells, full PBA-Zn battery systems studied thus far have typically reported only up to 100 cycles and suffer significant capacity fade beyond that. In this work we demonstrate that the loss in capacity retention and cycle life is a combined effect of Zn 2+ ion poisoning at the PBA cathode, as well as dendrite formation in the zinc anode. We address both these issues via the use of a dual ion (Na + as the primary charge carrier) electrolyte and hyper-dendritic Zinc (HD Zn) as the anode. The copper hexacyanoferrate (CuHcf) vs. HD Zn system with Na + ion electrolyte demonstrated herein exhibits 90% (83%) capacity retention after 300 (500) cycles at a 5C rate and a 3% reduction in usable capacity from 1C to 5C. Detailed characterization is done using in situ synchrotron energy-dispersive XRD (EDXRD), conventional XRD, XPS, SEM, TEM, and electrochemical techniques.

The low cost, significant reduction potential and relative safety of the zinc electrode is a common hope for a reductant in secondary batteries, but it is limited mainly to primary implementation due to shape change. In this work, we exploit such shape change for the benefit of static electrodes through the electrodeposition of hyper-dendritic nanoporous zinc foam. Electrodeposition of zinc foam resulted in nanoparticles formed on secondary dendrites in a three-dimensional network with a particle size distribution of 54.1-96.0 nm. The nanoporous zinc foam contributed to highly oriented crystals, high surface area and more rapid kinetics in contrast to conventional zinc in alkaline mediums. The anode material presented had a utilization of 88% at full depth-of-discharge (DOD) at various rates indicating a superb rate capability. The rechargeability of Zn 0 /Zn 2+ showed significant capacity retention over 100 cycles at a 40% DOD to ensure that the dendritic core structure was imperforated. The dendritic architecture was densified upon charge-discharge cycling and presented superior performance compared with bulk zinc electrodes.

A Bi2O3 in β-MnO2 composite cathode material has been synthesized using a simple hydrothermal method and cycled in a mixed KOH-LiOH electrolyte with a range of concentrations. We show that, at a KOH:LiOH molar ratio of 1:3, both proton insertion and lithium insertion occur, allowing access to a higher fraction of the theoretical capacity of the MnO2 while preventing the formation of ZnMn2O4. This enables a capacity of 360 mAh/g for over 60 cycles, with cycling limited more by anode properties than traditional cathodic failure mechanisms. The structural changes occurring during cycling are characterized using electron microscopy and in situ synchrotron energy-dispersive X-ray diffraction (EDXRD) techniques. This mixed electrolyte shows exceptional cyclability and capacity and can be used as a drop-in replacement for current alkaline batteries, potentially drastically improving their cycle life and creating a wide range of new applications for this energy storage technology.

An explanation of the correlation between “bounce” and state of charge of a zinc alkaline battery.

Alkaline iron electrodes present some challenges for use in secondary batteries that are associated with low coulombic efficiency and discharge utilization. Low coulombic efficiency is correlated to the hydrogen evolution reaction that takes place during charge. In this work, we demonstrate rechargeable alkaline iron electrodes with significant capacity retention over 150 cycles with high efficiency by suppressing the hydrogen evolution with stannate. Adding stannate to the alkaline electrolyte when cycling the iron electrode drastically changes the electrochemistry. The additive brings on two advantageous attributes for the iron electrode: increased hydrogen evolution overpotential, and a flat and prolonged discharge curve at typical battery operation. These attributes were provided by a novel intermediate phase that was detected from in situ neutron diffraction measurements. This phase was only detected in situ while it decomposed ex situ, and indicated a solid solution constituted by some of the elements present in the electrode.

An experimental setup and routine is presented for evaluating potential catalysts for water splitting by means of measuring the faradaic efficiency in real time through coupled potentiometry and mass spectrometry. The aim was to scale up an analytical cell unit towards the simulation of industrial conditions and generate results such as H 2 production versus power input at a certain potential or current density in addition to electrochemical parameters. Three types of electrodes were tested: A) planar metal electrodes; B) metal-foam-based electrodes; C) porous electrodes with carbon additive. The results verify that the experimental routine yields the desired accuracy, sensitivity, and a negligible accumulation of gaseous products in the cell; thus the faradaic efficiency is measured in real time. The metal-based electrodes of category A and B proved to be durable with low overpotentials and high gas output to power input, whereas three tested metal oxide electrodes in C revealed i) potential-dependent deviation in the faradaic efficiency, ii) phase decomposition, and iii) an optimum operational power range.

Fe-air or Ni-Fe cells can offer low-cost and large-scale sustainable energy storage. At present, they are limited by low coulombic efficiency, low active material use, and poor rate capability. To overcome these challenges, two types of nanostructured doped iron materials were investigated: (1) copper and tin doped iron (CuSn); and (2) tin doped iron (Sn). Single-wall carbon nanotube (SWCNT) was added to the electrode and LiOH to the electrolyte. In the 2 wt. % Cu + 2 wt. % Sn sample, the addition of SWCNT increased the discharge capacity from 430 to 475 mAh g−1, and charge efficiency increased from 83% to 93.5%. With the addition of both SWCNT and LiOH, the charge efficiency and discharge capacity improved to 91% and 603 mAh g−1, respectively. Meanwhile, the 4 wt. % Sn substituted sample performance is not on par with the 2 wt. % Cu + 2 wt. % Sn sample. The dopant elements (Cu and Sn) and additives (SWCNT and LiOH) have a major impact on the electrode performance. To understand the relation between hydrogen evolution and charge current density, we have used in operando charging measurements combined with mass spectrometry to quantify the evolved hydrogen. The electrodes that were subjected to prolonged overcharge upon hydrogen evolution failed rapidly. This insight could help in the development of better charging schemes for the iron electrodes.