Aircraft gas turbine blades operate in aggressive, generally oxidizing, atmospheres. A solution to mitigate the degradation and improve the performance of such components is the deposition of thermal barrier coatings (TBCs). Specifically for bond coats in aerospace applications, High Velocity Air Fuel (HVAF) is very efficient for coating deposition. However, internal diameter (ID) HVAF has received little attention in the literature and could be a promising alternative to limit oxidation during spraying when compared to conventional methods. The main objective of this study is to analyze how the ID-HVAF process influences the microstructure of NiCoCrAlY coatings. To that end, an i7 ID-HVAF torch is used to deposit NiCoCrAlY splats on a steel substrate with different stand-off distances. The deposited splats showed the presence of craters, and both partially melted and deformed particles at the surface. The particle velocity data was recorded, and the splat deformation and amount of particles deposited was shown to be directly corelated to the stand-off distance. The material composition analyzed and quantified by Energy Dispersive Spectroscopy (EDS) did not reveal any traces of in-flight of particle oxidation, but further investigation is required. This study provided a preliminary understanding towards the importance of stand-off distance on the splat deformation and in-flight oxidation.
The deposition of MCrAlX coatings (where M is Ni, Co, Fe, or a combination of these, and X is Y, Si, Ta, Hf, or a combination of these) via thermal spraying has acquired significant importance in industries such as aerospace, power plants, oil, and gas, etc. Among various thermal spray deposition techniques, high-velocity air fuel (HVAF) has shown a growing potential for the deposition of metallic powders which are sensitive to high-temperature oxidation during spraying. Thus, it is essential to understand the in-flight behavior of these metallic particles in the high-velocity, low-temperature HVAF flame. In this work, a NiCoCrAlY powder was sprayed using two sets of HVAF deposition parameters onto stainless steel substrates. In-flight particle diagnostic tools such as AccuraSpray were employed to understand the behavior of these spray particles. The deposited particles were comprised of partially molten particles and fully deformed splats. Samples with higher powder feed rates showed a primary coating buildup on the substrate surface. EDS plots revealed no traces of inflight particle oxidation but contained carbon residue due to the presence of unburnt hydrocarbons from the fuel-rich HVAF-M3 torch. This study provides a preliminary understanding towards the significance of deposition parameters on the in-flight particle oxidation behavior and splat deformation characteristics by HVAF spraying.
Erosion and abrasion are both wear processes in which a particle that strikes the surface removes material, either by impact (erosion) or contact (abrasion). These wear processes can cause damages to components, which can be protected by coatings to reduce the damage occurrence. Thermally sprayed coatings are considered candidates for a protective system against abrasion and erosion. The HVOF spray process is one of the most used thermal spray processes due to the ability of producing dense coatings, with good values of hardness and toughness. Among the materials used in thermally sprayed coatings, WC-Co based coatings are often used, as it offers a combination of high hardness, toughness and adherence, which can provide a good wear resistance. In this work, the influence of different HVOF process parameters, specifically the type of fuel used, on the residual stresses and properties of these coatings was studied. It was noted that coatings deposited by HVOF with kerosene liquid fuel, presented lower porosity, compared with coatings deposited by gas fuel. It was also observed that the coatings with lower porosity provide a better abrasion resistance, meanwhile the erosion was controlled by toughness for 30° and higher hardness for 60° of impact angle.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.