No abstract

No abstract

Abstract. Indonesia is a tropical country that has potential energy of solar radiation worth of 4.5 until 4.8 kWh/m 2 . However, this potential has not been utilized regularly. This paper will discuss the performance of solar collector compound parabolic concentrator (CPC) type with water as the working fluid. This CPC solar collector utilized three pipes covered by glass tubes. This paper has contribution to provide the temperature achievement between three pipes covered by glass tubes with and without glass cover of solar collector CPC type. The research conducted by varying the water flow rate of 1 l/m up to 6 l/m with three pipes arranged in series and parallel. From the results, the used of solar collector CPC type in the current study shows that the decrease of solar radiation, which was caused by climate change, did not influence the heat absorbance by water in the pipe. Therefore, the design of the solar collector in this research has potential to be used in future when solar radiation are used as the energy source.

A new design of a vacuum freeze drying with internal cooling and heater from condenser’s heat loss was built and tested. The dryer was used to dry jelly fish (scyphomedusae) to study the effect of drying parameter such as temperature within the drying chamber on mass losses (evaporation) during freezing stage and moisture ratio at the end of drying process and also the drying rate of vacuum drying process. The cold trap temperature rise in when activated the heating from condenser’s heat loss. The midili thin layer mathematical drying model was used to estimate and predict the moisture ratio curve base on different drying chamber temperature. The result of this experiment show that mass loss during freezing stage decreased with a decrease in drying chamber temperature with constant pressure. Drying time reduced with an increase in drying temperature. Drying chamber temperature decreasing has a result pressure saturation of material lower than drying chamber pressure have an effect mass transfer should not occurs.

Thermal Efficiency of Organic Rankin Cycle (ORC) Power Plant System from low-grade heat resources using various working fluids has been analyzed based on the simulation. Four working fluids, namely R-134a, R-32, R-407A, and R-422C were selected on the simulated ORC system to determine its thermal efficiency in some temperature set up of evaporator and condenser. The working fluids are simulated with mass flow rate of 0.15 kg/s at evaporator exit temperature of 75°C, 80°C, and 85°C and at condenser exit temperature of 20°C to 50°C at each 5°C temperature difference. Fluid properties in these conditions are analyzed with REFPROP software then become data input for Cycle Tempo simulation. The thermal efficiency values of each temperature and refrigerant variation are then analyzed to obtain optimum value and variation for the simulated ORC system. The efficiency was obtained at the evaporator exit temperature of 75°C and condenser exit temperature of 45°C. ORC simulation revealed that the optimum and realistic working fluid was R-32 with thermal efficiency of 7.03 %.

No abstract

Leaf waste has the potential to be converted into energy because of its high availability both in the world and Indonesia. Gasification is a conversion technology that can be used to convert leaves into producer gas. This gas can be used for various applications, one of which is using it as fuel for gas turbines, including ultra-micro gas ones, which are among the most popular micro generators of electric power at the time. To minimize the risk of failure in the experiment and cost, simulation is used. To simulate the performance of gas turbines, the thermodynamic analysis tool called Cycle-Tempo is used. In this study, Cycle-Tempo was used for the zero-dimensional thermodynamic simulation of an ultra-micro gas turbine operated using producer gas as fuel. Our research contributions are the simulation of an ultra-micro gas turbine at a lower power output of about 1 kWe and the use of producer gas from leaf waste gasification as fuel in a gas turbine. The aim of the simulation is to determine the influence of air-fuel ratio on compressor power, turbine power, generator power, thermal efficiency, turbine inlet temperature and turbine outlet temperature. The simulation was carried out on condition that the fuel flow rate of 0.005 kg/s is constant, the maximum air flow rate is 0.02705 kg/s, and the air-fuel ratio is in the range of 1.55 to 5.41. The leaf waste gasification was simulated before, by using an equilibrium constant to get the composition of producer gas. The producer gas that was used as fuel had the following molar fractions: about 22.62% of CO, 18.98% of H2, 3.28% of CH4, 10.67% of CO2 and 44.4% of N2. The simulation results show that an increase in air-fuel ratio resulted in turbine power increase from 1.23 kW to 1.94 kW. The generator power, thermal efficiency, turbine inlet temperature and turbine outlet temperature decreased respectively from 0.89 kWe to 0.77 kWe; 3.17% to 2.76%; 782 °C to 379 °C and 705°C to 304 °C. The maximums of the generator power and thermal efficiency of 0.89 kWe and 3.17%, respectively, were obtained at the 1.55 air-fuel ratio. The generator power and thermal efficiency are 0.8 kWe and 2.88%, respectively, with the 4.64 air-fuel ratio or 200% excess air. The result of the simulation matches that of the experiment described in the literature.

No abstract