Hydrogen embrittlement (HE) is a critical issue that hinders the reliability of hydrogenation reactors. Hence, it is of great significance to investigate the effect of hydrogen on fracture toughness of 2.25Cr-1Mo-0.25V steel and weld. In this work, the fracture behavior of 2.25Cr-1Mo-0.25V steel and welds was studied by three-point bending tests under hydrogen-free and hydrogen-charged conditions. The immersion charging method was employed to pre-charge hydrogen inside specimen and the fracture toughness of these joints was evaluated quantitatively. The microstructure and grain size of the specimens were observed by scanning electron microscopy (SEM) and by metallurgical microscopy to investigate the HE mechanisms. It was found that fracture toughness for both the base metal (BM) and the weld zone (WZ) significantly decreased under hydrogen-charged conditions due to the coexistence of the hydrogen-enhanced decohesion (HEDE) and hydrogen-enhanced localized plasticity (HELP) mechanisms. Moreover, the formation and growth of primary voids were observed in the BM, leading to a superior fracture toughness. In addition, the BM compared to the WZ shows superior resistance to HE because the finer grain size in the BM leads to a larger grain boundary area, thus distributing more of the diffusive hydrogen trapped in the grain boundary and reducing the hydrogen content.

No abstract

No abstract

No abstract

The 2.25Cr-1Mo-0.25V steels are widely used in the petroleum chemical industry for the manufacturing of pressure vessels. The multi-pass welding is a critical type of fabrication in hydrogenation reactor. However, very complicated residual stresses could be generated during the multi-pass welding process. The presence of residual stresses could have significant influence on the performance of welded product. In the present work, the transient temperature distribution and residual stress distribution in welding of 2.25Cr-1Mo-0.25V steel are analyzed by using numerical method. An uncoupled thermal-mechanical two-dimensional (2-D) FEM is proposed under the ABAQUS environment. The transient temperature distribution and the residual stress distribution during the welding processes are determined through the finite element method. A group of experiments by using the blind-hole method have been conducted to validate the numerical results. The results of 2-D model agree well with the experiment. The result shows that the maximum welding stress generated at heat affected zone (HAZ) both at the top and bottom surface whether to transverse stress or longitudinal stress.

Hydrogenation reactors are important oil-refining equipment that operate in high-temperature and high-pressure hydrogen environments and are commonly composed of 2.25Cr–1Mo–0.25V steel. For a hydrogenation reactor with a plate-welding structure, the processes and effects of welding residual stress (WRS) are very complicated due to the complexity of the welding structure. These complex welding residual stress distributions affect the service life of the equipment. This study investigates the evolution of welding residual stress during weld-overlay cladding for hydrogenation reactors using the finite element method (FEM). A blind hole method is applied to verify the proposed model. Unlike the classical model, WRS distribution in a cladding/substrate system in this study was found to be divided into three regions: the cladding layer, the stress-affected layer (SAL), and the substrate in this study. The SAL is defined as region coupling affected by the stresses of the cladding layer and substrate at the same time. The evolution of residual stress in these three regions was thoroughly analyzed in three steps with respect to the plastic-strain state of the SAL. Residual stress was rapidly generated in Stage 1, reaching about −440 MPa compression stress in the SAL region at the end of this stage after 2.5 s. After cooling for 154 s, at the end of Stage 2, the WRS distribution was fundamentally shaped except for in the cladding layer. The interface between the cladding layer and substrate is the most heavily damaged region due to the severe stress gradient and drastic change in WRS during the welding process. The effects of substrate thickness and preheat temperature were evaluated. The final WRS in the cladding layer first increased with the increase in substrate thickness, and then started to decline when substrate thickness reached a large-enough value. WRS magnitudes in the substrate and SAL decreased with the increase in preheat temperature and substrate thickness. Compressive WRS in the cladding layer, on the other hand, increased with the increase in preheat temperature.

The carbide characteristics of 2.25Cr1Mo0.25V steel have an extremely important influence on the mechanical properties of welding joints. In addition, hydrogen resistance behavior is crucial for steel applied in hydrogenation reactors. The carbide morphology was observed by scanning electron microscopy (SEM) and the carbide microstructure was characterized by transmission electron microscopy (TEM). Tensile and impact tests were carried out and the influence of carbides on properties was studied. A hydrogen diffusion test was carried out, and the hydrogen brittleness resistance of welding metal and base metal was studied by tensile testing of hydrogenated samples to evaluate the influence of hydrogen on the mechanical properties. The research results show that the strength of the welding metal was slightly higher and the Charpy impact value was significantly lower compared to the base metal. The hydrogen embrittlement resistance of the welding metal was stronger than that of the base metal. The presence of more carbides and inclusions was the main cause of the decreased impact property and hydrogen brittleness resistance of the welding metal. These conclusions have certain reference value for designing and manufacturing hydrogenation reactors.

The heat affected zone (HAZ) of 2.25Cr-1Mo-0.25V welded joint is a critical part for the safety of hydrogenation reactors. Hydrogen has a significant effect on the HAZ, studying hydrogen diffusion characteristics, such as: hydrogen flux and the effective hydrogen diffusivity has a remarkable value in investigating the hydrogen-induced material degradation mechanisms. In this work, an electrochemical permeation method was applied to study the hydrogen diffusion characteristics of HAZ. Then, the metallographic microscope and a software “Image J” were used to analyze the density of grain boundaries of HAZ. The effect of the post–weld heat treatment (PWHT, i.e. annealing) on the hydrogen diffusion characteristics of HAZ was also been investigated. The results show that after PWHT, the effective hydrogen diffusivity of HAZ increases from 1.63 × 10−7cm2·s−1 to 3.68 × 10−7cm2·s−1, the hydrogen concentration decreases from 1.92 × 10−4mol·cm−3 to 1.09 × 10−4mol·cm−3, and the hydrogen trap density decreases from 3.00 × 1026m−3 to 0.76 × 1026m−3. Thus, PWHT can significantly reduce density of grain boundaries, thereby reducing the hydrogen trap density, enhancing the hydrogen diffusivity and reducing the hydrogen concentration.