The mechanical performance of wood floors were evaluated. Denser woods presented highest mechanical strength. A new table of mechanical performance classes was proposed. Reference values can be used for predicting mechanical behaviour of wood floors of unknown species.
This study aimed to determine the basic density of the wood and to simulate the performance of flooring produced with wood from five tropical species: Dipteryx odorata (Cumaru), Handroanthus spp. (Ipê), Hymenaea Courbaril (Jatobá), Astronium Lecointei (Muiracatiara), and Bowdichia virgilioides (Sucupira-Preta). Falling steel sphere, static and dynamic friction, indentation caused by loads applied in small areas, rolling load, and abrasiveness impact tests were simulated. The results were subjected to analysis of variance and Tukey’s test at 5% significance, and Pearson’s correlation was performed between the basic density and the indexes of each flooring. The basic density of the wood flooring made from the evaluated species ranged from 0.735 to 0.958 g.cm-3. D. odorata, Handroanthus spp. and H. courbaril woods were classified as heavy, while those of A. Lecointei and B. Virgilioides as moderately heavy. It was possible to indicate D. odorata, Handroanthus spp., H. courbaril, and B. Virgilioides flooring for environments with intense traffic where there is dragging or falling objects such as industries and companies. The A. Lecointei flooring can be used in residential environments with light traffic, where the loads exerted are low. There was a correlation between the basic wood density and the flooring use simulation tests.
A escassez de informações sobre as características das madeiras de mogno africano e de sua trabalhabilidade limitam sua utilização e introdução no mercado madeireiro. Os objetivos foram avaliar a qualidade da superfície usinada e comparar o consumo de energia específica de corte entre as espécies das madeiras de Khaya ivorensis e Khaya senegalensis com diferentes padrões de usinagem. Para avaliar a qualidade da superfície usinada, foi utilizada uma desempenadeira com rotações de 2400, 3600 e 4000 min-1 e velocidade de avanço de 6 e 15 m*min-1. A qualidade da superfície foi avaliada por meio do avanço por dente (fz), avaliação visual e rugosidade. Cortes longitudinais e transversais foram realizados por serra circular com rotações de 2500, 3000 e 3500 min-1 para obtenção da energia de corte específica, por meio de um inversor de frequência. A espécie K. senegalensis apresentou consumo de energia de corte 10% superior a K. ivorensis, já no corte transversal houve maior consumo de 36% da K. senegalensis. Pela qualificação visual as melhores superfícies usinadas foram provenientes da velocidade de avanço de 6 m*min-1. A rugosidade não variou em função dos diferentes parâmetros de usinagem e nem entre as duas espécies.
The aim of this work was to evaluate the effect of thermal modification on surface hardness and depressions by applying loads to obtain floors for low traffic environments. Four clones were used from which logs were obtained and split into boards dried in time, and grouped for testing in their natural condition (NT) and thermally modified at 200 degrees Celsius for four hours (T) in a schedule with a heating of 1 degree per minute, on electric oven. Then in the samples from each clone were evaluated the mass loss, specific gravity, lignin and holocelluloses content, Janka hardness, fall ball impact depressions, distributed load depressions, and concentrated load depressions using track equipment which transfer a load of 890N to the woods at a speed of 0.06 ms-1. In the results verified high mass loss in the E. grandis x E. urophylla clone from controlled polination. The lignin contents showed increases and holocelluloses contents showed significant decreases after thermal modification. There was a reduction in Janka hardness in the woods with the exception of E. urophylla clone which presented lower depressions in the fall ball test after thermal modification. Verified increasing in depressions in the concentrated and distributed load tests, after thermal modification. And the E. urophylla clone presented lower depressions after 25 and 50 passes respectively, being the most recommended for obtaining floors for saunas, garden decks, swimming pools as it does not require high loading requirements.
A segurança do trabalho é importante em todas as atividades, pois a falta de ações para prevenir e diminuir os acidentes causam prejuízos para o trabalhador afastado e para a produção da empresa. Em fábricas de móveis e marcenarias onde existe o processamento mecânico com diferentes tipos de máquinas e diversidade de madeiras a realidade não é diferente. Os elevados níveis de pressão sonora emitido pelas máquinas está relacionado com doenças de perda auditiva induzida pelo ruído (PAIR). Dessa forma o objetivo deste trabalho foi realizar um levantamento dos níveis de ruído contínuo/intermitente de fábricas de móveis no Brasil. O trabalho foi realizado por meio de buscas na literatura utilizando metodologia sistemática, seleção e extração das informações relevantes. Todos os valores de nível de ruído e dose nos trabalhos pesquisados ficaram acima do permitido por lei. Assim, podendo caracterizar os ambientes estudados como insalubres ao ruído e com risco iminente a saúde dos trabalhadores. Dessa forma, para evitar doenças, como a PAIR, é necessário o uso de medidas preventivas nos ambientes laborais e o uso de protetores auriculares.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
334 Leonard St
Brooklyn, NY 11211
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.