ABSTRAK:Bahan bakar alternatif diperlukan untuk pengganti sumber daya alam yang tidak dapat diperbarui.Salah satu bahan bakar alternatif tersebut yang dikembangkan adalah briket arang dengan memanfaatkan limbah biomassa.Pada penelitian ini dibuat briket arang dengan mengkaji pengaruh variasi tekanan pengepresan dan komposisi bahan terhadap sifat fisis briket arang. Proses karbonisasi pada tempurung kelapa 450ºC selama 15 menit. Serbuk kayu dikarbonisasi menggunakan klin drum selama 4-5 jam. Perbandingan komposisi bahan tempurung kelapa dengan serbuk kayu adalah sebagai berikut 75%:25%, 25%:75%, 50%:50%, 100%:0%, 0%: 100% dengan tekanan pengepresan 50 N/cm 2 , 100 N/cm 2 ,150N/cm 2 . Pengeringan briket dilakukan di dalam oven dengan suhu 60°C selama 24 jam. Briket berbentuk silinder dengan diameter 5 cm.Hasil penelitian menunjukkan briket paling optimum dengan perbandingan komposisi bahan 100% tempurung kelapa menggunakan tekanan antara 100-150 N/cm 2 dengan nilai parameter uji sebagai berikut densitas 0.634 gr/cm 3 , kekuatan mekanik 43.167 N/cm 2 dan lama pembakaran 64,39 menit.Kata Kunci: tekanan pengepresan, komposisi bahan, sifat fisis dan briket arang ABSTRACT:The alternative fuel was needed to substitute the natural resource that can not be renewed. One of alternative fuels developed was charcoal briquette by examining the influence of pressing pressure variation and material composition to the physical features of charcoal briquette. The study was conducted in a laboratory scale using carbonization process in the coconut shell at 450 º C for 15 minutes. Wood powder was carbonized by using a drum kiln for 4-5 hours. The Comparison of the composition of coconut shell with wood powder is as follows 75%:25%, 25%:75%, 50%:50%, 100%:0%, 0%:100% with pressing pressure of 50kg/cm 2 , 100 kg/cm 2 , 150 kg/cm 2 . This research remains variable with adhesive tapioca starch and 30% of cow dung. Briquette drying was in an oven with a temperature of 60°C for 24 hours. Briquette shaped cylinder with a diameter of 5 cm.The best results were obtained briquettes are briquettes with a composition ratio of 100% coconut shell using a pressure of 100-150kg/cm 2 with the following test parameter values 0634 gr/cm 3 density, mechanical strength of 43.167 N/cm 2 and the duration of combustion of 64,39 minutes
Background: Treatment of wounds in diabetes often gets less than perfect healing. One of the reasons for the difficulty in treating wounds in diabetes is the growth of aerobic and anaerobic bacteria. This study aims to determine the pulse voltage and treatment time that can optimally inactivate bacteria, and their effect on wound healing in mice suffering from diabetes. Methods: The study used electrical stimulation with a direct voltage of 10 volts given a pulse voltage of 50-80 volts, a width of 50 µs, and the number of pulses of 65 per second. The research samples were Staphylococcus aureus (S. aureus) and Pseudo-monas aeruginosa (P. aeruginosa) bacteria that grew on beef and mice (Mus musculus) with diabetes. The treatment for S. aureus and P. aeruginosa bacteria was carried out using a pulse voltage of 50-80 volts for 5-15 min/day and repeated for 3 days. Meanwhile, treatment of mice wounds was carried out with a pulse voltage of 80 volts for 15 min/day and repeated for 7 days. Results: The results showed that treatment with a pulse voltage of 50-80 volts and a treatment time of 5-15 min significantly reduced the number of S. aureus and P. aeruginosa bacteria in beef (p£0.05). Treatment with a pulse voltage of 80 volts for 15 min made beef free from bacteria. Meanwhile, treatment with a pulse voltage of 80 volts for 15 min per day for seven days resulted in the wound state of three mice in the maturation phase and two mice in the proliferation phase on day 8 with an average wound area of 0.108 cm 2. Conclusion: The treatment with a pulse voltage of 80 volts for 15 min made the beef sterile, the mice wounds healed quickly, and the mice not stressed. The higher the blood glucose level, the slower the wound healing process.
Telah dilakukan suatu upaya memodifikasi dan rekayasa turbin jenis cross-flow. Rekayasa dilakukan dengan merubah jumlah sudut dan hubungannya dengan jumlah putaran, daya turbin, dan efisiensi turbin. Rekayasa juga dilakukan terhadap bentuk saluran yang digunakan yaitu saluran terbuka berbentuk persegi, setengah lingkaran dan trapesium. Penelitian ini dilakukan dengan mengambil beberapa input yang disesuaikan dengan kebanyakan yang ada di lapangan. Input yang diambil adalah kecepatan alir, tinggi jatuh, kemiringan saluran, lebar penampang saluran, jari-jari saluran, diameter luar turbin, dan lebar turbin. Sementara itu besaran yang dibuat variabel adalah jumlah sudu pada turbin cross-flow. Penampang sebagai saluran air dipakai persegi, setengah lingkaran, dan trapesium dan ketiganya dibuat terbuka. Hasil penelitian menunjukkan bahwa dengan asumsi lebar penampang 4 m, tinggi jatuh 2 m, jari-jari 2 m, kemiringan 1/√3, kecepatan aliran 2 m/s, diameter luar turbin 0,75 m, dan lebar turbin 4,3 m, maka turbin dengan jumlah sudu 12 memiliki jumlah putaran, daya turbin, dan efisiensi turbin yang paling besar. Bilamana jumlah sudu diperbanyak, maka jumlah putaran, daya turbin, dan efisiensi turbin semakin kecil. Sementara itu penelitian untuk menentukan jenis penampang saluran didapatkan bahwa jenis saluran dengan penampang trapesium dihasilkan jumlah putaran, daya turbin, dan efisiensi turbin yang paling besar disusul jenis persegi dan setengah lingkaran.<br /><br />Kata Kunci : Energi air, Turbin cross-flow, Jumlah sudut.<br /><br />
Bahan bakar minyak merupakan bahan bakar yang diolah dari sumber daya alam yang tidak dapat diperbaharui. Biomassa merupakan sumber enrgi alternatif terbarukan yang berasal dari tumbuh-tumbuhan dan limbah. Tempurung kelapa dapat diolah menjadi arang yang merupakan bahan baku pembuatan arang briket dengan proses karbonisasi. Temperatur karbonisasi sangat berpengaruh terhadap arang yang dihasilkan sehingga penentuan temperatur yang tepat akan menentukan kualitas arang. Penelitian ini merupakan penentuan nilai kalor dari arang tempurung kelapa dengan suhu pengarangan yang berbeda. Variasi suhu pengarangan yang diberikan yaitu 200 C, 250 ˚ C, 300 C, 350 ˚ C, 400 C, 500 C, 550 ˚ C, dengan pengulangan sebanyak tiga kali pada setiap variasi suhu. Penelitian ini bertujuan untuk mengetahui pengaruh suhu pada proses pengarangan terhadap nilai kalor arang. Selain itu mengetahui efisiensi pembuatan arang tempurung kelapa dengan menganalisa perubahan massa bahan sebelum dan sesudah pengarangan. Metode penelitian yang digunakan dalam penelitian ini adalah deskriptif kuantitatif yang ditampilkan dalam bentuk table dan grafik, kemudian data yang dihasilkan dianalisis dengan anova dan regresi linier. Hasil penelitian ini menunjukkan bahwa penyusutan massa dan nilai kalor berbanding lurus dengan tingginya suhu pengarangan. semakin tinggi suhu pengarangan, penyusutan massa bahan semakin tinggi dan nilai kalor semakinbesar.<br /><br /><br /><br />
Globally, sesame consumption continues to increase, so it requires additional production to balance. Often there are obstacles in the production process, both technique and the presence of pests. One way to increase production is to treat it with a magnetic field during seed growth and germination. This study aims to determine the magnetic flux density (MFD) to obtain the optimal stem growth, chlorophyll content, fruit size, and plant resistance to Fusarium oxysporum. The seeds are processed by giving treatment using a MFD of 0.0-0.5 mT, which oscillates with a frequency of 50 Hz. Plant seeds were treated using a magnetic field every day for five days with a treatment time of 20 minutes each. The results showed that sesame seeds treated with magnetic fields had earlier emergence time of sprouts, higher stems, more chlorophyll content, faster flowering, larger fruit sizes, and more resistance to F. oxysporum wilt attacks. Treatment with a MFD of 0.3 mT resulted in optimal plant growth, health, and resistance to F. oxysporum attack. Treatment of seeds using magnetic fields ranging from wetting the seeds to germinating makes the plants healthier, bigger fruits, and more resistant to F. oxysporum wilt attacks.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.