The objectives of this study were (1) to determine in vitro changes in surface roughness and color of dental resin composites after application of three finishing and polishing systems; (2) to evaluate the difference in color stability after immersion in a dye solution after polishing; and (3) to evaluate the effects of surface condition, especially roughness, on measured color depending on the color measuring geometries of specular component excluded (SCE) and specular component included (SCI). Color and surface roughness (R(a)) of resin composites of four brands of A2 shade and one brand of Yellow Enamel shade were measured after polymerization, after polishing with Enhance (Dentsply), Sof-Lex (3M ESPE), or Super-Snap (Shofu) composite finishing and polishing systems. Color was also measured after immersion in 2% methylene blue solution. Color was measured according to the CIELAB color scale. Color changes (DeltaE*(ab)) after polishing/staining and by the measuring geometry were calculated by the equation; DeltaE*(ab) = [(DeltaL*)(2) + (Deltaa*)(2) + (Deltab*)(2)](1/2). Ra value was measured with a surface roughness tester. DeltaE*(ab) and DeltaL* values after polishing and after staining varied among polishing systems when measured with SCE geometry. Composites polished with Super-Snap and Sof-Lex systems showed higher DeltaE*(ab) and DeltaL* values than those polished with Enhance polishing system with SCE geometry. DeltaE*(ab) and DeltaL* values between specimens with different surface conditions measured with SCE geometry were significantly higher than those with SCI (p < 0.01). Changes in R(a) value after polishing was insignificant in most cases.
Identifying the occurrences of proper names in text and the entities they refer to can be a difficult task because of the manyto-many mapping between names and their referents. We analyze the types of ambiguity --structural and semantic --that make the discovery of proper names difficult in text, and describe the heuristics used to disambiguate names in Nominator, a fully-implemented module for proper name recognition developed at the IBM T.J. Watson Research Center.
The oral absorption of omeprazole is incomplete, in part due to first-pass metabolism. We investigated the feasibility of rectal administration of omeprazole by comparing its absorption from a Witepsol H15-based rectal suppository and an orally administered commercial gelatin capsule in 10 male volunteers. Profiles of plasma concentration between two preparations (20 mg) were not statistically different, indicating that the rate and the extent of absorption were similar. Paired t-test revealed no significant differences in area under the curve, mean residence time, and time to peak concentration between two preparations. On the other hand, lag time of absorption and peak concentration were statistically different (p< 0.05) between these preparations. Under these experimental conditions, the rectal route did not produce an improvement in the extent of absorption over an oral capsule.
The objective of this study was to determine the changes in color and translucency of dental porcelain-repairing resin composites compared to dental porcelain after thermocycling. Color and spectral reflectance of three shades (A2, A3, and A3.5) of one brand of dental porcelain and three basic shades (A2, A3, and A3.5) and three combinations (A2/A3, A3/3.5, and A2/A3.5) of three brands of porcelain-repairing resin composites (ABT, FSP, and TCR) were measured, before and after thermocycling for 3000 cycles, relative to the illuminant D65. The specimen was 2 mm in thickness, and 1 mm of each shade was layered to make combined shades. Changes in color (DeltaE*ab) and translucency parameter (DeltaTP) were calculated. A general linear model by the material (porcelain or resin composite) and shade was used to compare differences (alpha = 0.05). The range of color changes was 0.68-1.67 in porcelain, 0.56-1.30 in ABT, 2.28-3.10 in FSP, and 0.36-1.15 in TCR. The range of DeltaTP was 0.45-0.96 in porcelain, -0.48 to 0.94 in ABT, -1.31 to 0.82 in FSP, and -0.51 to 1.91 in TCR. After thermocycling, changes in color and TP were correlated with the shade of the material, but not with the material. The discrepancy in the changes of color and translucency after thermocycling between porcelain and porcelain-repairing resin composites should be considered when selecting repairing materials.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.