Polylactic acid (PLA) is one of the most suitable materials for 3D printing. Blending with nanoparticles improves some of its properties, broadening its application possibilities. The article presents a study of composite PLA matrix filaments with added unmodified and lignin/polymerised lignin surface-modified nanofibrillated cellulose (NFC). The influence of untreated and surface-modified NFC on morphological, mechanical, technological, infrared spectroscopic, and dynamic mechanical properties was evaluated for different groups of samples. As determined by the stereo and scanning electron microscopy, the unmodified and surface-modified NFCs with lignin and polymerised lignin were present in the form of plate-shaped agglomerates. The addition of NFC slightly reduced the filaments’ tensile strength, stretchability, and ability to absorb energy, while in contrast, the initial modulus slightly improved. By adding NFC to the PLA matrix, the bending storage modulus (E’) decreased slightly at lower temperatures, especially in the PLA samples with 3 wt% and 5 wt% NFC. When NFC was modified with lignin and polymerised lignin, an increase in E’ was noticed, especially in the glassy state.
In the present research, the properties of ultraviolet (UV) visible (daylight invisible) fluorescent coatings modified by the addition of SiO2 and TiO2 nanoparticles were studied. Structural, surface, and mechanical properties and changes in the coatings caused by accelerated ageing were analyzed. The results showed that the addition of nanoparticles caused the changes in unaged and aged printed coatings. Reflectance measurements of modified coatings showed that addition of TiO2 nanoparticles improved the visual effect of the unaged coatings. Furthermore, results have shown that the addition of SiO2 did not diminish the reflectance of the modified coatings after ageing. The results of roughness measurements showed that the addition of SiO2 decreased roughness after the ageing process, probably due to the degradation process indicated by Attenuated Total Reflection Fourier Transform Infrared (ATR-FTIR) spectroscopy. The roughness of the coatings with TiO2 nanoparticles was increased after the ageing on the samples with higher concentrations of TiO2 due to the agglomerates of plastisol formed on the surface of the coatings, visible in SEM images. Surface analysis of coatings showed that TiO2 caused an increase in the polarity of the surface coatings. Results of the bending stiffness showed that the addition of the nanoparticles to the coating, especially of SiO2, significantly improved the bending stiffness of the unaged samples.
Invasive alien plant species (IAPS) are one of the biggest challenges in European ecosystems, displacing local vegetation, destroying agricultural land, and causing billions of dollars of damage to the European economy every year. Many of them are removed daily and mainly burned. In this work, we investigated the possibilities of using plants as feedstock for paper production. Papers made from three invasive alien plants, i.e., Knotweed, Goldenrod, and Black locust, were studied and compared with commercial office paper. The study included testing of: (1) structural properties—basic physical properties, grammage, thickness, density and specific volume, moisture content, and ash content; (2) physical and dynamic mechanical properties—tensile strength, Clark stiffness, viscoelastic properties; (3) colorimetric properties of prints; (4) effect of UV light on ageing; and (5) study of cellulose fiber structure and morphology by microscopy. The results suggested that the paper produced can be used as commercial office paper, considering that the paper is slightly dyed. Such papers can also be used for special purposes that present a natural style and connection to nature. The papers produced can also be used for printing documents that are meant to be kept.
The purpose of the study is to investigate the possibility of using wine industry wastes, such as red and white grape bagasse, to produce bacterial cellulose (BC) instead of using a costly commercial medium. BC was produced using grape bagasse as a carbon source replacement and the sole nutrient in the medium. The BC films were evaluated for their productivity and water-holding capacity. The BC films were also investigated for their morphology using scanning electron microscopy (SEM), their viscoelastic properties using dynamic mechanical analysis (DMA), and their chemical composition using Fourier-transform infrared spectroscopy (FTIR). Although the use of grape bagasse as the sole nutrient was successful in the preparation of BC, the BC films had inferior viscoelastic properties to other produced BC films. White grape bagasse proved to be an excellent carbon substitute as the production of BC and its water-holding capacity were five times higher and the produced BC films were up to 72% more flexible than the bacterial cellulose produced using standard HS medium.
Polyamide 6 (PA6) composite filament yarns were produced by the simultaneous incorporation of melamine cyanurate (MeCy) with multiwalled carbon nanotubes (CNTs) and carbon black (CB) into a composite matrix in a melt-spinning process. The results show that the simultaneous incorporation of MeCy with CNTs or CB additives provided filaments with a uniform black color. Tensile analysis confirmed that a reinforcing effect was achieved when CB was used, whereas the CNTs induced a reducing effect on the filament tenacity. With regard to the burning behavior, the flame-retardant action of MeCy was preserved in the presence of CB but was significantly hindered when used in combination with CNTs. These results indicate that the mixture of MeCy and CB was much more compatible for the production of reinforced PA6 composite filaments with increased thermal stability and improved flame retardancy over those of the MeCy and CNTs.
Studies of the production of fiber-forming polyamide 6 (PA6)/graphene composite material and melt-spun textile fibers are scarce, but research to date reveals that achieving the high dispersion state of graphene is the main challenge to nanocomposite production. Considering the significant progress made in the industrial mass production of graphene nanoplatelets (GnPs), this study explored the feasibility of production of PA6/GnPs composite fibers using the commercially available few-layer GnPs. To this aim, the GnPs were pre-dispersed in molten ε-caprolactam at concentrations equal to 1 and 2 wt %, and incorporated into the PA6 matrix by the in situ water-catalyzed ring-opening polymerization of ε-caprolactam, which was followed by melt spinning. The results showed that the incorporated GnPs did not markedly influence the melting temperature of PA6 but affected the crystallization temperature, fiber bulk structure, crystallinity, and mechanical properties. Furthermore, GnPs increased the PA6 complex viscosity, which resulted in the need to adjust the parameters of melt spinning to enable continuous filament production. Although the incorporation of GnPs did not provide a reinforcing effect of PA6 fibers and reduced fiber tensile properties, the thermal stability of the PA6 fiber increased. The increased melt viscosity and graphene anti-dripping properties postponed melt dripping in the vertical flame spread test, which consequently prolonged burning within the samples.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.