No abstract

This study aims to clarify the influence of additive elements of Ni and Mn on tensile and impact properties of three kinds of spheroidal graphite cast irons (SG irons), which are as cast, annealed and austempered samples. Spheroidal graphite cast irons with Ni (0-4?5 mass-%) and Mn (0-0?5 mass-%) melted by a high frequency induction furnace and cast into a Y block CO 2 mould with 30 mm in thickness. From the viewpoint of heat treatment, tensile strength and hardness of SG irons become larger in the order of ferritised,as cast,austempered ones. Matrix structures of SG irons, which are conducted to austempering treatment from a and c mixture range, consists of bainitic ferrite with high toughness. Austempered SG iron with 3%Ni in 0?1%Mn series is found to become higher tensile strength compound with elongation and toughness of 901 MPa, 17% and 915 kJ m 22 .

This study aims to clarify the influence of external notch on impact characteristics of high toughness ductile cast irons prepared by austempering heat treatment. We produced ductile cast irons samples with various matrix microstructure tested by Charpy impact within five kinds of external notches whose stress concentration factors (α), with values taken from 1.0 (Unnotched) to 4.8. In addition, to clarify the initiation process of impact characteristics, we observed the evolution of microstructure surface during bending tests with a slow loading speed for the un-notched and the notched impact samples. The results showed that the impact fracture energy decreases strongly in the range of α from 1 to 2.3 but decreases slightly for α larger than 3.Moreover, the impact value of samples with austempered microstructure is sensitive to the external notch shape. The impact transition temperature increases with increasing the stress concentration factor. The fracture energy is decreasing with the external notch from the impact test since the crack initiation energy is directly affected by this later. This work contributes to get a better understanding in the basic theories of external notch effect on impact characteristics of austempered spheroidal graphite cast irons (ADI).

Recently, high-entropy alloys (HEAs) have attracted much attention because of their superior properties, such as high strength and corrosion resistance. This study aimed to investigate the influences of process parameters on the microstructure and mechanical properties of CoCrFe NiTiMo HEAs using a laser-based powder bed fusion (LPBF) process. In terms of laser power and scan speed, a process map was constructed by evaluating the density and surface roughness of the as-built specimen to optimize the process parameters of the products. The mechanical properties of the as-built specimens fabricated at the optimum fabrication condition derived from the process map were evaluated. Consequently, the optimum laser power and scan speed could be obtained using the process map evaluated by density and surface roughness. The as-built specimen fabricated at the optimum fabrication condition presented a relative density of more than 99.8%. The microstructure of the as-built specimen exhibited anisotropy along the build direction. The tensile strength and elongation of the as-built specimen were around 1150 MPa and more than 20%, respectively.

The object of this study is to find out and evaluate systematically how the basic factors such as graphite-shape, external notch and matrix-characteristic affect the impact and bending characteristics of cast irons. The Spheroidal Graphite (SG) and Compacted Vermicular graphite (CV) cast iron samples were prepared, and their matrixes were modified into ferritic, pearlitic and bainitic in order to make the various kinds of samples whose graphite-shape and matrix vary widely. From each sample we produced five kinds of Charpy-type specimens by adding five kinds of notches whose stress concentration factor (α) varied from 1.0 (un-notched) to 4.8. The Charpy impact value decreases greatly in the range of α from 1 to 2.3 but decreases slightly in the range of α larger than 2.3. No influence to the fracture energy in the range of α larger than 2.3. Increasing of α results in moderate elevation of transition temperature of Charpy impact value and the transition temperature of CV cast ion is lower than that of SG one. The impact value in brittle fracture region of the cast iron samples were recognized to be a little bit larger than that of cast steel sample, and it was considered to be caused by graphite which act as a kind of buffer effect against crack growth in brittle fracture.

No abstract

In order to clarify the potential of bulk amorphous alloys as a new class of structural materials with high dimensional stability, the thermal expansion and magnetic properties of amorphous Fe56Co7Ni7Zr10B20 doped with Cr have been investigated. Both the magnetic moment and the Curie point of amorphous Fe56Co7Ni7Zr10B20 were suppressed by Cr addition. The effect of Cr on the magnetic moment was well described by assuming a reduction of 4μB∕Cr atom. It was found that the Curie temperature can be controlled by Cr content over a wide range of 200K in the vicinity of room temperature. Although Invar characteristics were absent from the thermal expansion curves, amorphous Fe56Co7Ni7Zr10B20 doped with 1at.% Cr was found to exhibit a small coefficient of thermal expansion comparable to Kovar alloys, indicating that bulk amorphous alloys may have a potential for commercial low expansion materials.

No abstract