With a high theoretical specific energy, the non-aqueous rechargeable lithium-oxygen battery is a promising next-generation energy storage technique. However, the large charging overpotential remains a challenge due to the difficulty in electrochemically oxidizing the insulating lithium peroxide. Recently, a redox shuttle has been introduced into the electrolyte to chemically oxidize lithium peroxide. Here, we report the use of a triiodide/iodide redox shuttle to couple a built-in dye-sensitized titanium dioxide photoelectrode with the oxygen electrode for the photoassisted charging of a lithium-oxygen battery. On charging under illumination, triiodide ions are generated on the photoelectrode, and subsequently oxidize lithium peroxide. Due to the contribution of the photovoltage, the charging overpotential is greatly reduced. The use of a redox shuttle to couple a photoelectrode and an oxygen electrode offers a unique strategy to address the overpotential issue of non-aqueous lithium-oxygen batteries and also a distinct approach for integrating solar cells and batteries.

Recent investigations into the application of potassium in the form of potassium-oxygen, potassium-sulfur, and potassium-ion batteries represent a new approach to moving beyond current lithium-ion technology. Herein, we report on a high capacity anode material for use in potassium-oxygen and potassium-ion batteries. An antimony-based electrode exhibits a reversible storage capacity of 650 mAh/g (98% of theoretical capacity, 660 mAh/g) corresponding to the formation of a cubic K3Sb alloy. The Sb electrode can cycle for over 50 cycles at a capacity of 250 mAh/g, which is one of the highest reported capacities for a potassium-ion anode material. X-ray diffraction and galvanostatic techniques were used to study the alloy structure and cycling performance, respectively. Cyclic voltammetry and electrochemical impedance spectroscopy were used to provide insight into the thermodynamics and kinetics of the K-Sb alloying reaction. Finally, we explore the application of this anode material in the form of a K3Sb-O2 cell which displays relatively high operating voltages, low overpotentials, increased safety, and interfacial stability, effectively demonstrating its applicability to the field of metal oxygen batteries.

Exploring new p-type semiconductor nanoparticles alternative to the commonly used NiO is crucial for p-type dye-sensitized solar cells (p-DSSCs) to achieve higher open-circuit voltages (Voc). Here we report the first application of delafossite CuGaO2 nanoplates for p-DSSCs with high photovoltages. In contrast to the dark color of NiO, our CuGaO2 nanoplates are white. Therefore, the porous films made of these nanoplates barely compete with the dye sensitizers for visible light absorption. This presents an attractive advantage over the NiO films commonly used in p-DSSCs. We have measured the dependence of Voc on the illumination intensity to estimate the maximum obtainable Voc from the CuGaO2-based p-DSSCs. Excitingly, a saturation photovoltage of 464 mV has been observed when a polypyridyl Co(3+/2+)(dtb-bpy) electrolyte was used. Under 1 Sun AM 1.5 illumination, a Voc of 357 mV has been achieved. These are among the highest values that have been reported for p-DSSCs.

Superoxide based metal-air (or metal-oxygen) batteries, including potassium and sodium-oxygen batteries, have emerged as promising alternative chemistries in the metal-air battery family because of much improved round-trip efficiencies (>90%). In order to improve the cycle life of these batteries, it is crucial to understand and control the side reactions between the electrodes and the electrolyte. For potassium-oxygen batteries using ether-based electrolytes, the side reactions on the potassium anode have been identified as the main cause of battery failure. The composition of the side products formed on the anode, including some reaction intermediates, have been identified and quantified. Combined experimental studies and density functional theory (DFT) calculations show the side reactions are likely driven by the interaction of potassium with ether molecules and the crossover of oxygen from the cathode. To inhibit these side reactions, the incorporation of a polymeric potassium ion selective membrane (Nafion-K(+)) as a battery separator is demonstrated that significantly improves the battery cycle life. The K-O2 battery with the Nafion-K(+) separator can be discharged and charged for more than 40 cycles without increases in charging overpotential.

Proton reduction is one of the most fundamental and important reactions in nature. MoS2 edges have been identified as the active sites for hydrogen evolution reaction (HER) electrocatalysis. Designing molecular mimics of MoS2 edge sites is an attractive strategy to understand the underlying catalytic mechanism of different edge sites and improve their activities. Herein we report a dimeric molecular analogue [Mo2 S12 ](2-) , as the smallest unit possessing both the terminal and bridging disulfide ligands. Our electrochemical tests show that [Mo2 S12 ](2-) is a superior heterogeneous HER catalyst under acidic conditions. Computations suggest that the bridging disulfide ligand of [Mo2 S12 ](2-) exhibits a hydrogen adsorption free energy near zero (-0.05 eV). This work helps shed light on the rational design of HER catalysts and biomimetics of hydrogen-evolving enzymes.

p-Type dye-sensitized solar cells (p-DSCs) have attracted increasing attention recently, but they suffer from low fill factors (FFs) and unsatisfactory efficiencies. A full comprehension of the hole transport and recombination processes in the NiO p-DSC is of paramount importance for both the fundamental study and the practical device optimization. In this article, NiO p-DSCs were systematically probed under various bias and illumination conditions using electrochemical impedance spectroscopy (EIS), intensity modulated photocurrent spectroscopy (IMPS), and intensity modulated photovoltage spectroscopy (IMVS). Under the constant 1 sun illumination, the recombination resistance (R rec ) of the cell deviates from an exponential relationship with the potential and saturates at ∼130 Ω cm 2 under the short circuit condition, which is ascribed to the overwhelming recombination with the reduced dye anions. Such a small R rec results in the small dc resistance, which decreases the "flatness" of the J−V curve. The quantitative analysis demonstrates that the FF value is largely attenuated by the recombination of holes in NiO with the reduced dyes. Our analysis also shows that if this recombination can be eliminated, then an FF value of 0.6 can be reached, which agrees with the theoretical calculation with a V oc of 160 mV.

The research of p-type dye-sensitized solar cells (p-DSSCs) has attracted growing attention because of the potential for integration with conventional n-type DSSCs (n-DSSCs) into the more efficient tandem-DSSCs. However, to date the performance of p-DSSCs is lagging behind that of n-DSSCs. One main reason is the lack of optimal photocathode materials. This article reviews the most recent progress in utilizing Cu(I)-based delafossite compounds, CuMO2 (M = Al, Ga or Cr), as photocathodes in p-DSSCs. As alternative materials to the commonly used NiO, the CuMO2 compounds have their intrinsic advantages such as lower valence band edge, larger optical bandgap and higher conductivity. By providing an insight into these materials and their applications in p-DSSCs, this perspective aims to stimulate more exciting research in the development of p-DSSCs as well as of tandem-DSSCs.

Integrating both photoelectric-conversion and energy-storage functions into one device allows for the more efficient solar energy usage. Here we demonstrate the concept of an aqueous lithium-iodine (Li-I) solar flow battery (SFB) by incorporation of a built-in dye-sensitized TiO2 photoelectrode in a Li-I redox flow battery via linkage of an I3(-)/I(-) based catholyte, for the simultaneous conversion and storage of solar energy. During the photoassisted charging process, I(-) ions are photoelectrochemically oxidized to I3(-), harvesting solar energy and storing it as chemical energy. The Li-I SFB can be charged at a voltage of 2.90 V under 1 sun AM 1.5 illumination, which is lower than its discharging voltage of 3.30 V. The charging voltage reduction translates to energy savings of close to 20% compared to conventional Li-I batteries. This concept also serves as a guiding design that can be extended to other metal-redox flow battery systems.