Tandem dye-sensitized photoelectrochemical cells (DSPECs) for water splitting are a promising method for sustainable energy conversion but so far have been limited by their lack of aqueous stability and photocurrent mismatch between the cathode and anode. In nature, membrane-enabled subcellular compartmentation is a general approach to control local chemical environments in the cell. The hydrophobic tails of the lipid make the bilayer impermeable to ions and hydrophilic molecules. Herein we report the use of an organic donor-acceptor dye that prevents both dye desorption and semiconductor degradation by mimicking the hydrophobic/hydrophilic properties of lipid bilayer membranes. The dual-functional photosensitizer (denoted as BH4) allows for efficient light harvesting while also protecting the semiconductor surface from protons and water via its hydrophobic π linker. The protection afforded by this membrane-mimicking dye gives this system excellent stability in extremely acidic (pH 0) conditions. The acidic stability also allows for the use of cubane molybdenum-sulfide cluster as the hydrogen evolution reaction (HER) catalyst. This system produces a proton-reducing current of 183 ± 36 μA/cm(2) (0 V vs NHE with 300 W Xe lamp) for an unprecedented 16 h with no degradation. These results introduce a method for developing high-current, low-pH DSPECs and are a significant move toward practical dye-sensitized solar fuel production.

Integrating both photoelectric-conversion and energy-storage functions into one device allows for the more efficient solar energy usage. Here we demonstrate the concept of an aqueous lithium-iodine (Li-I) solar flow battery (SFB) by incorporation of a built-in dye-sensitized TiO2 photoelectrode in a Li-I redox flow battery via linkage of an I3(-)/I(-) based catholyte, for the simultaneous conversion and storage of solar energy. During the photoassisted charging process, I(-) ions are photoelectrochemically oxidized to I3(-), harvesting solar energy and storing it as chemical energy. The Li-I SFB can be charged at a voltage of 2.90 V under 1 sun AM 1.5 illumination, which is lower than its discharging voltage of 3.30 V. The charging voltage reduction translates to energy savings of close to 20% compared to conventional Li-I batteries. This concept also serves as a guiding design that can be extended to other metal-redox flow battery systems.

Herein, we report three novel single donor double acceptor dyes, BH2, 4, and 6, for use in p-type dye sensitized solar cells (DSSCs). BH4 yields one of the highest photocurrents, 7.4 mA cm(-2), to date. The high performance is achieved via a shorter synthetic route and no exotic materials or cell-building techniques. We suggest a structural principle when building dyes whereby one adopts a double acceptor/single anchor when a triphenylamine moiety is incorporated into a dye for p-type DSSCs. This strategy increases the molar extinction coefficient while simultaneously reducing the number of synthetic steps. The molar extinction coefficients (99 980 M(-1) cm(-1)) reported herein are among the highest reported. Finally, we report the first-ever-observed light soaking effect in p-type DSSCs.

Efficient sensitized photocathodes are highly desired for solar fuels and tandem solar cells, yet the development is hindered by the scarcity of suitable p-type semiconductors. The generation of high cathodic photocurrents by sensitizing a degenerate n-type semiconductor (tin-doped indium oxide; ITO) is reported. The sensitized mesoporous ITO electrodes deliver cathodic photocurrents of up to 5.96±0.19 mA cm(-2), which are close to the highest record in conventional p-type sensitized photocathodes. This is realized by the rational selection of dyes with appropriate energy alignments with ITO. The energy level alignment between the highest occupied molecular orbital of the sensitizer and the conduction band of ITO is crucial for efficient hole injection. Transient absorption spectroscopy studies demonstrate that the cathodic photocurrent results from reduction of the photoexcited sensitizer by free electrons in ITO. Our results reveal a new perspective toward the selection of electrode materials for sensitized photocathodes.

Efficient sensitized photocathodes are highly desired for solar fuels and tandem solar cells, yet the development is hindered by the scarcity of suitable p‐type semiconductors. The generation of high cathodic photocurrents by sensitizing a degenerate n‐type semiconductor (tin‐doped indium oxide; ITO) is reported. The sensitized mesoporous ITO electrodes deliver cathodic photocurrents of up to 5.96±0.19 mA cm−2, which are close to the highest record in conventional p‐type sensitized photocathodes. This is realized by the rational selection of dyes with appropriate energy alignments with ITO. The energy level alignment between the highest occupied molecular orbital of the sensitizer and the conduction band of ITO is crucial for efficient hole injection. Transient absorption spectroscopy studies demonstrate that the cathodic photocurrent results from reduction of the photoexcited sensitizer by free electrons in ITO. Our results reveal a new perspective toward the selection of electrode materials for sensitized photocathodes.