Poly(L-lysine)-g-poly(ethylene glycol) (PLL-g-PEG) is a member of a family of polycationic PEG-grafted copolymers that have been shown to chemisorb on anionic surfaces, including various metal oxide surfaces, providing a high degree of resistance to protein adsorption. PLL-g-PEG-modified surfaces are attractive for a variety of applications including sensor chips for bioaffinity assays and blood-contacting biomedical devices. The analytical and structural properties of PLL-g-PEG adlayers on niobium oxide (Nb2O5), tantalum oxide (Ta2O5), and titanium oxide (TiO2) surfaces were investigated using reflection-absorption infrared spectroscopy (RAIRS), angle-dependent X-ray photoelectron spectroscopy (XPS), and time-of-flight secondary ion mass spectrometry (ToF-SIMS). The combined analytical information provides clear evidence for an architecture with the cationic poly(L-lysine) attached electrostatically to the oxide surfaces (charged negatively at physiological pH) and the poly(ethylene oxide) side chains extending out from the surface. The relative intensities of the vibrational modes in the RAIRS spectra and the angle-dependent XPS data point to the PLL backbone being located directly at and parallel to the oxide/polymer interface, whereas the PEG chains are preferentially oriented in the direction perpendicular to the surface. Both positive and negative ToF-SIMS spectra are dominated by PEG-related secondary ion fragments with strongly reduced metal (oxide) intensities pointing to an (almost) complete coverage by the densely packed PEG comblike grafts. The three different transition metal oxide surfaces with isoelectric points well below 7 were found to behave very similarly, both in respect to the kinetics of the polymer adlayer adsorption and properties as well as in terms of protein resistance of the PLL-g-PEG-modified surface. Adsorption of serum and fibrinogen was evaluated using the OWLS optical planar waveguide technique. The amount of human serum adsorbed on the modified surfaces was consistently below the detection limit of the optical sensor technique used (<1-2 ng cm -2 ), and fibrinogen adsorption was reduced by 96-98% in comparison to the nonmodified (bare) oxide surfaces.

Poly(L-lysine)-g-poly(ethylene glycol) (PLL-g-PEG) copolymers with various grafting ratios were adsorbed to niobium pentoxide-coated silicon wafers and characterized before and after protein adsorption using X-ray photoelectron spectroscopy (XPS) and time-of-flight secondary ion mass spectrometry (ToF-SIMS). Three proteins of different sizes, myoglobin (16 kD), albumin (67 kD), and fibrinogen (340 kD), were studied. XPS was used to quantify the amount of protein adsorbed to the bare and PEGylated surfaces. ToF-SIMS and principal component analysis (PCA) were used to study protein conformational changes on these surfaces. The smallest protein, myoglobin, generally adsorbed in higher numbers than the much larger fibrinogen. Protein adsorption was lowest on the surfaces with the highest PEG chain surface density and increased as the PEG layer density decreased. The highest adsorption was found on lysine-coated and bare niobium surfaces. ToF-SIMS and PCA data evaluation provided further information on the degree of protein denaturation, which, for a particular protein, were found to decrease with increasing PEG surface density and increase with decreasing protein size.

No abstract

Dodecyl phosphate and hydroxy-terminated dodecyl phosphate are shown to spontaneously assemble on smooth titanium oxide and titanium metal coated glass and silicon substrates, as well as on rough titanium metal implant surfaces. The surfaces were dipped in aqueous solutions of the corresponding ammonium salts for 48 h. The molecules are shown by X-ray photoelectron spectroscopy (XPS) to form densely packed, self-assembled monolayers (SAMs) on all surfaces investigated. The phosphate headgroups are believed to attach to the titanium (oxide) surface with the terminal end group (either methyl or hydroxy) pointing toward the ambient environment (air, vacuum, or water). Mixed SAMs are shown to be formed from mixed aqueous solutions of the two amphiphiles, with the hydroxy-terminated dodecyl phosphate adsorbing more favorably than the methyl-terminated molecule. The advancing water contact angles can be easily tailored via the composition of the self-assembly solution in the range of 110° (pure methyl) to 55° (pure hydroxy) on flat, smooth titanium surfaces. Surface roughness strongly modifies the wetting properties, with advancing contact angles in the range of 150−100° being observed, as well as the degree of hysteresis (difference between advancing and receding angles). Model calculations based on XPS intensities have been successfully used to quantify the adlayer composition and molecular surface densities across the whole range of mixed adlayer chemistry. The organophosphate monolayers on titanium are believed to have a significant potential for precise control of the surface chemistry and interfacial tension on both smooth and rough titanium surfaces in application areas such as medical implants and other devices where independent control of surface chemistry and topography is essential to performance.

Titanium is widely used in biomedical applications. Its mechanical properties and biocompatibility, conferred by a layer of oxide present on its surface, make titanium the material of choice for various implants (artificial hip and knee joints, dental prosthetics, vascular stents, heart valves). Furthermore, the high refractive index of titanium oxide is advantageous in biosensor applications based on optical detection methods. In both of the above fields of application, novel surface modification strategies leading to biointeractive interfaces (that trigger specific responses in biological systems) are continuously sought. In this report, we investigate the interactions between TiO2 and phosphatidyl serine-containing liposomes, present a novel approach for preparing supported phospholipid bilayers (SPBs) of various compositions on TiO2, and use the unique ability of liposomes to distinguish between different surfaces to create SPB corrals on SiO2/TiO2 structured substrates. These results represent an important first step toward the design of biointeractive interfaces on titanium oxide surfaces that are based on a cell membrane-like environment.

No abstract

No abstract

Alkanethiolates have been widely used as chemisorbates to modify gold surfaces, in spite of their relatively poor oxidative stability. We introduce gold-chemisorbing block copolymers bearing an anchoring block of poly(propylene sulphide) (PPS), selected in the expectation of greater stability. These materials offer a more robust approach to surface modification of gold. As an example, a triblock copolymer with poly(ethylene glycol) (PEG) was selected, with the goal of minimizing biological adsorption and adhesion. The copolymer PEG17-bl-PPS25-bl-PEG9 chemisorbed to form a dense monolayer of 226 +/- 26 ng cm(-2), approximately 2.2 nm thick. The copolymeric adlayer was much more stable to oxidation than commonly used alkanethiolates. Its presence greatly reduced protein adsorption (>95%), even after exposure to whole blood serum (>55 mg x ml(-1)), as well as cell adhesion over long culture durations (>97%). PPS-containing copolymers are an attractive alternative to alkanethiolates, and PEG-bl-PPS-bl-PEG presents a powerful example for use in biodiagnostic and bioanalytical devices.