In tilting-pad journal bearings (TPJB) with a non-flooded lubrication concept, higher maximum pad temperatures occur than with a flooded bearing design due to the lower convective heat transfer at the pad edges. In this paper, we present an approach to influence the thermal behavior of a five-pad TPJB by active cooling. The aim of this research is to investigate the influence of additional oil supply grooves at the trailing edge of the two loaded pads on the maximum pad temperature of a large TPJB in non-flooded design. We carry out experimental and numerical investigations for a redesigned test bearing. Within the experimental analysis, the reduction in pad temperature is quantified. A simulation model of the bearing is synthesized with respect to the additional oil supply grooves. The simulation results are compared with the experimental data to derive heat transfer coefficients for the pad surfaces. The experimental results indicate a considerable reduction of the maximum pad temperatures. An overall lower temperature level is observed for the rear pad in circumferential direction (pad 4). The authors attribute this effect by a cooling oil carry-over from the previous pad (3). Within the model limits, a good agreement of the simulation and experimental results can be found.

In tilting-pad journal bearings (TPJB), power loss corresponds to the internal friction in the shearing of the oil. Besides the lubrication gap, intermediate spaces between the pads account for a notable amount of frictional losses. Against the background of increasing demands for efficiency and sustainable use of resources, the reduction of power loss takes a key position in the further development of bearings. In our research, we compare two bearing lubrication concepts of a five-pad TPJB. Our objective is to work out the influence of different lubrication methods and bearing housing designs on the bearing operation characteristics. We conduct experimental testing of a 500mm TPJB in two different bearing configurations with respect to the lubrication concept: an oil-flooded and non-flooded bearing design. In the flooded bearing design, oil is supplied via spray-bars and axial seals ensure the inter-pad spaces to be completely filled with oil. The non-flooded design comes without axial seals but oil drain channels to avoid oil accumulation in the bearing. In the latter design, oil is fed in via leading edge grooves (LEG). For the non-flooded bearing design, the experimental data show that the unloaded pads are not completely filled with oil and therefore, no pressure build-up occurs. The absence of additional load on the lower pads compared to the flooded design results in an increase of minimum film thickness. With the non-flooded design, power loss at high speeds is reduced to almost half. As a result, the efficiency of the entire turbomachinery application can be considerably improved.

An increase of specific load in large tilting pad journal bearings (TPJB) leads to major mechanically and thermally induced deformation of the pads and limits the load carrying capacity. In this paper, we present a theoretical approach to determine deformation of a TPJB with PEEK (Polyetheretherketone) polymer lined pads by means of a thermo-elasto-hydrodynamic model. The objective of this investigation is a quantitative analysis of the deformation characteristics of a five-pad TPJB with a nominal diameter of 500 mm. Mechanical and thermal deformations are simulated for both the steel backing and the polymer lining. The deformation characteristics calculated with the numerical model are compared to simulation results of an experimentally validated model with a white-metal lining. The results indicate an improvement in bearing characteristics with the PEEK lining, as maximum pressure decreases and minimum film thickness increases. Due to the insulating properties of the PEEK layer, thermally induced pad deformation is reduced significantly.

A large tilting-pad journal bearing (TPJB) with “PEEK” polymer-lined pads was tested over a range of operating conditions representative of those experienced on turbogenerators used in fossil fuel power plants. The 500 mm diameter test-bearing has four offset-pivot pads, ball and socket pivots, load-between-pivot configuration, directed lubrication and hydrostatic jacking features. The operating conditions explored during the test campaign characterize the static and dynamic behaviour of the bearing over a range of shaft surface speeds between 40 m/s and 95 m/s and maximum specific load of 4.75 MPa. Similar test conditions were previously investigated on the same bearing with whitemetal lined pads, allowing for a direct comparison. A thermo-elasto-hydrodynamic (TEHD) model for TPJBs with polymer-lined pads is introduced in this paper and validated against experimental test data. Experimental data along with numerical results reveal and confirm the superior performance that can be attained using TPJBs with polymer lined pads at high specific loads.

Improving efficiency is a general task in the design process of high-speed journal bearings. A specific fixed-pad bearing geometry featuring reduced pad length and additional design measures with the intention of reducing frictional power loss is investigated, experimentally and theoretically, for a journal diameter of 500 mm up to surface speeds of 94 m/s and unit loads of 5.0 MPa. To model fluid flow in the bearing outside the lubricant gap, an extension to Elrod’s cavitation algorithm based on assuming the inertia of fluid flow is proposed. Validation of the extended thermo-elasto-hydrodynamic lubrication (TEHL) model shows good agreement between measurement and prediction in wide operating ranges, however, with systematic tendencies of the remaining deviations. Furthermore, measured local pressure and film thickness distributions indicate a complex formation of cavitation with an influence of axial flow that is not covered by pure Couette-flow in the cavitation region. Measured as well as predicted data prove increased bearing efficiency for high rotor speeds. To provide understanding on the impact of the applied design measures improving efficiency, their combination is separated into the individual ones. Reduced axial and peripheral pad length both contribute almost equally to the reduction in power loss and improve its value by 37% compared to the standard design. Finally, further steps to deeper identify the behavior of the bearing are comprehensively discussed.

No abstract