Injuries to the anterior cruciate ligament frequently occur under combined mechanisms of knee loading. This in vitro study was designed to measure levels of ligament force under dual combinations of individual loading states and to determine which combinations generated high force. Resultant force was recorded as the knee was extended passively from 90 degrees of flexion to 5 degrees of hyperextension under constant tibial loadings. The individual loading states were 100 N of anterior tibial force, 10 Nm of varus and valgus moment, and 10 Nm of internal and external tibial torque. Straight anterior tibial force was the most direct loading mechanisms; the mean ligament force was approximately equal to applied anterior tibial force near 30 degrees of flexion and to 150% of applied tibial force at full extension. The addition of internal tibial torque to a knee loaded by anterior tibial force produced dramatic increases of force at full extension and hyperextension. This loading combination produced the highest ligament forces recorded in the study and is the most dangerous in terms of potential injury to the ligament. In direct contrast, the addition of external tibial torque to a knee loaded by anterior tibial force decreased the force dramatically for flexed positions of the knee; at close to 90 degrees of flexion, the anterior cruciate ligament became completely unloaded. The addition of varus moment to a knee loaded by anterior tibial force increased the force in extension and hyperextension, whereas the addition of valgus moment increased the force at flexed positions. These states of combined loading also could present an increased risk for injury. Internal tibial torque is an important loading mechanism of the anterior cruciate ligament for an extended knee. The overall risk of injury to the ligament from varus or valgus moment applied in combination with internal tibial torque is similar to the risk from internal tibial torque alone. External tibial torque was a relatively unimportant mechanism for generating anterior cruciate ligament force.

Biparietal diameter measurement is the most widely accepted means of determining gestational age. However, a standard anatomic plane for performing this measurement has not been established. Three hundred forty-four measurements on 256 patients who gave birth to normal infants were obtained and compared at various cranial levels based on brain anatomy. The results document that use of a standardized plane increases measurement reliability but does not significantly alter variability. We postulate that variability is based predominantly on biologic variation in fetal growth rates rather than on technical errors.

No abstract

We assessed the accuracy of magnetic resonance imaging in detecting clinically significant lesions of the anterior horn of the meniscus by reviewing 947 consecutive knee magnetic resonance imaging reports. Of these, 76 (8%) indicated a tear of the anterior horn of the medial or lateral meniscus. Thirty-one of these 76 patients underwent a subsequent arthroscopic examination, and their operative reports were reviewed. The 45 patients who were not examined arthroscopically were contacted and interviewed for clinical follow-up. Among the 31 patients who underwent arthroscopic examination, 8 anterior horn tears were noted in the predicted area (26% true-positive results), 23 patients had intact anterior horns (74% false-positive results), and 18 had normal intact menisci in all zones. Of the 45 patients who did not undergo arthroscopic surgery, 6 had isolated anterior horn tears reported on magnetic resonance imaging, and 5 of the 6 were asymptomatic at follow-up. The other 39 patients had multiple pathologic conditions noted on the magnetic resonance imaging report and continued to report knee pain at the follow-up interview. Increased signal intensity at the anterior horn of the meniscus seen on magnetic resonance imaging commonly does not represent a clinically significant lesion. We recommend correlation with the physical examination when interpreting this "positive" finding on knee magnetic resonance imaging examinations.

Pedicle screw constructs have been shown to increase fusion rates in the lumbar spine. Manufacturers have created pedicle screws with one or two degrees of freedom built into the screw head to allow for easier incorporation of the interlocking rod, but the effects of these screws on construct stiffness has not been tested. The purpose of this study is to compare and contrast the stiffness of lumbar pedicle screw constructs with and without the use of polyaxial pedicle screws. Nontapered, self-taping pedicle screws (6.0-mm diameter x 30-mm length, titanium) were used in the fixation of porcine spines from L3-L5. Group 1 (n = 5) contained six standard pedicle screws from one manufacturer. Group 2 (n = 5) contained six standard pedicle screws from a second manufacturer. Group 3 (n = 5) contained four standard pedicle screws placed at L3 and L5, as well as two polyaxial screws placed at L4. Group 4 (n = 5) contained six polyaxial pedicle screws. A rotational variable differential transformer was used to record angular displacement between vertebrae in the construct as it is loaded in flexion, extension, right bend, left bend, clockwise torque, and counterclockwise torque. Stiffness curves were linear throughout the range of applied force. The average r2 value for the generated stiffness graphs was 0.94 (SD = 0.06). No construct failure occurred during any of the testing. There were no significant differences (p < 0.05, two-way analysis of variance) in moment versus angle noted in any of the four groups tested. For torque tests, the all-polyaxial screw constructs showed significantly increased stiffness compared with the other groups. The current study has shown that the incorporation of polyaxial screws in pedicle screw constructs did not significantly decrease the construct stiffness. There is a suggestion that the use of all polyaxial screws may increase the resistance to torque by allowing better purchase of intervertebral rods.

This study was performed to examine the effects of partial and total transection of the interosseous membrane (IOM) on load transfer in the foream. Twenty fresh frozen forearms were instrumented with custom designed load cells placed in the proximal radius and distal ulna. Simultaneous measurements of load cell forces, radial head displacement relative to the capitellum, and local tension within the central band of the IOM were made as the wrist was loaded to 134 N with the forearm at 90" of elbow flexion and in neutral pronation supination. For valgus elbow alignment (radial head contacting the capitellum), mean force carried by the distal ulna was 7.1% of the applied wrist force and mean force transferred from radius to ulna through the IOM was 4.4%. For varus elbow alignment (mean 2.0 mm gap between the radial head and capitellum), mean distal ulna force was 28Yn and mean IOM force was 51%. Section of the proximal and distal one-thirds of the IOM had no significant effect upon mean distal ulnar force or mean IOM force. Total IOM section significantly increased mean distal ulnar force for varus elbow alignment in all wrist positions tested. The mean level of applied wrist force necessary to close the varus gap (89 N) decreased significantly after both partial IOM section (71 N) and total IOM section (25 N). The IOM became loaded only when the radius displaced proximally relative to the ulna, closing the gap between the radius and capitellum. As the radius displaced proximally, the wrist becomes increasingly ulnar positive, which in turn leads to direct loading of the distal ulna. This shift of force to the distal ulna could present clinically as ulnar sided wrist pain or as ulnar impaction after IOM injury.

The superior labrum may be most vulnerable to injury in late cocking. The reproducible generation of type II superior labral anterior posterior lesions may have applications as a biomechanical model.

No abstract