An effective approach to significantly increase the electrical conductivity of a NiOx hole-transporting layer (HTL) to achieve high-efficiency planar heterojunction perovskite solar cells is demonstrated. Perovskite solar cells based on using Cu-doped NiOx HTL show a remarkably improved power conversion efficiency up to 15.40% due to the improved electrical conductivity and enhanced perovskite film quality. General applicability of Cu-doped NiOx to larger bandgap perovskites is also demonstrated in this study.

The ability to measure microsecond- and nanosecond-scale local dynamics below the diffraction limit with widely available atomic force microscopy hardware would enable new scientific studies in fields ranging from biology to semiconductor physics. However, commercially available scanning-probe instruments typically offer the ability to measure dynamics only on time scales of milliseconds to seconds. Here, we describe in detail the implementation of fast time-resolved electrostatic force microscopy using an oscillating cantilever as a means to measure fast local dynamics following a perturbation to a sample. We show how the phase of the oscillating cantilever relative to the perturbation event is critical to achieving reliable sub-cycle time resolution. We explore how noise affects the achievable time resolution and present empirical guidelines for reducing noise and optimizing experimental parameters. Specifically, we show that reducing the noise on the cantilever by using photothermal excitation instead of piezoacoustic excitation further improves time resolution. We demonstrate the discrimination of signal rise times with time constants as fast as 10 ns, and simultaneous data acquisition and analysis for dramatically improved image acquisition times.

An elegant method for the electrodeposition of MoS2 thin films using room temperature ionic liquids (RTIL) as an electrolyte was developed. Simple molecular precursors of Mo and S were added in different concentrations to tune the composition and deposition process. The electrodeposition of MoS2 was confirmed with both Raman spectroscopy and XPS. Analysis showed that the electrodeposited MoS2 films form a flower shape morphology with edge active sites that promote the hydrogen evolution reaction (HER). Furthermore, this technique enables selective tuning of the film thickness and demonstrates high photoluminescence activity with a decrease in the number of layers.

We investigate zirconium (Zr) incorporation into the titanium dioxide (TiO2) electron-transporting layer used in organometal halide perovskite photovoltaics. Compared to Zr-free controls, solar cells employing electrodes containing Zr exhibit increased power conversion efficiency (PCE) and decreased hysteresis. We use transient photovoltage and photocurrent extraction to measure carrier lifetimes and densities and observe longer carrier lifetimes and higher charge densities in devices on Zr-containing electrodes at microsecond times as well as longer persistent photovoltages extending from ∼milliseconds to tens of seconds. We characterize the surface stoichiometry and change in work function and reduction potential of the TiO2 upon incorporation of Zr and discuss the charge recombination at the TiO2 interface in the context of these variables. Finally, we show that the combination of Zr-TiO2 electrode modification with device pyridine treatment leads to a cumulative improvement in performance.

We study surface photovoltage decays on sub-millisecond time scales in organic solar cells using intensity-modulated scanning Kelvin probe microscopy (SKPM). Using polymer/fullerene (poly[N-9"-heptadecanyl-2,7-carbazole-alt-5,5-(4',7'-di-2-thienyl-2',1',3'-benzothiadiazole)]/[6,6]-phenyl C71-butyric acid methyl ester, PCDTBT/PC71BM) bulk heterojunction devices as a test case, we show that the decay lifetimes measured by SKPM depend on the intensity of the background illumination. We propose that this intensity dependence is related to the well-known carrier-density-dependent recombination kinetics in organic bulk heterojunction materials. We perform transient photovoltage (TPV) and charge extraction (CE) measurements on the PCDTBT/PC71BM blends to extract the carrier-density dependence of the recombination lifetime in our samples, and we find that the device TPV and CE data are in good agreement with the intensity and frequency dependence observed via SKPM. Finally, we demonstrate the capability of intensity-modulated SKPM to probe local recombination rates due to buried interfaces in organic photovoltaics (OPVs). We measure the differences in photovoltage decay lifetimes over regions of an OPV cell fabricated on an indium tin oxide electrode patterned with two different phosphonic acid monolayers known to affect carrier lifetime.