This paper investigates the usability of the GNSS PPP methods, traditional PPP with a floatambiguity solution and with Ambiguity Resolution (PPP-AR), in structural health monitoring applications based on experimental tests using a single-axis shaking table. To evaluate the performance of the PPP methodologies, harmonic oscillations of the motion table with amplitudes ranging from 5 mm to 20 mm and frequency between 0.2 Hz and 2.5 Hz were generated representing a wide range of possible structural motions. In addition, ground motion similar to those experienced during a real earthquake, the Kobe (1995), and step motions were generated on the shaking table. GNSS-PPP-derived positioning results were compared, in both of the frequency and time domains, with reference data comprising LVDT (Linear Variable Differential Transformer) data and relative positioning data. Results show that both PPP methods' measurements can be used in the computation of the harmonic oscillations' frequencies compared to the LVDT and relative positioning values. The observed amplitudes of the harmonic oscillations are slightly different from the LVDT values in the order of millimeters. Results of step motion experiment demonstrated that PPP-AR is better than traditional PPP in exhibiting the quasi-static or static displacement offsets. In addition, the capability of PPP-AR method is evaluated to the natural frequency of a small-scale structural model excited on the shaking table. The frequency spectrum of this small-scale structural model derived from the PPP-AR method is consistent with FEM (Finite Element Model) predicted value. All results demonstrate the potential of the high-rate GNSS PPP methods to reliably monitor structural and earthquake-induced vibration frequencies and amplitudes for both the structural and seismological applications.
Nowadays, the high rate GNSS (Global Navigation Satellite Systems) positioning methods are widely used as a complementary tool to other geotechnical sensors, such as accelerometers, seismometers, and inertial measurement units (IMU), to evaluate dynamic displacement responses of engineering structures. However, the most common problem in structural health monitoring (SHM) using GNSS is the presence of surrounding structures that cause multipath errors in GNSS observations. Skyscrapers and high-rise buildings in metropolitan cities are generally close to each other, and long-span bridges have towers, main cable, and suspender cables. Therefore, multipath error in GNSS observations, which is typically added to the measurement noise, is inevitable while monitoring such flexible engineering structures. Unlike other errors like atmospheric errors, which are mostly reduced or modeled out, multipath errors are the largest remaining unmanaged error sources. The high noise levels of high-rate GNSS solutions limit their structural monitoring application for detecting load-induced semi-static and dynamic displacements. This study investigates the estimation of accurate dynamic characteristics (frequency and amplitude) of structural or seismic motions derived from multipath-affected high-rate GNSS observations. To this end, a novel hybrid model using both wavelet-based multiscale principal component analysis (MSPCA) and wavelet transform (MSPCAW) is designed to extract the amplitude and frequency of both GNSS relative- and PPP- (Precise Point Positioning) derived displacement motions. To evaluate the method, a shaking table with a GNSS receiver attached to it, collecting 10 Hz data, was set up close to a building. The table was used to generate various amplitudes and frequencies of harmonic motions. In addition, 50-Hz linear variable differential transformer (LVDT) observations were collected to verify the MSMPCAW model by comparing their results. The results showed that the MSPCAW could be efficiently used to extract the dynamic characteristics of noisy dynamic movements under seismic loads. Furthermore, the dynamic behavior of seismic motions can be extracted accurately using GNSS-PPP, and its dominant frequency equals that extracted by LVDT and relative GNSS positioning method. Its accuracy in determining the amplitude approaches 91.5% relative to the LVDT observations.
In recent years, the continuously operating reference station-Turkey (CORS-TR) system has been widely used in engineering and cadastral work in Turkey due to ease of use, low cost, and national legislative requirements. In this study, long-term Network RTK (Real-time Kinematic) data were collected under 10°, 20°, 30° and 40° satellite views using a different approach from previous work. In order to evaluate the positioning performance of the system, the measurements were undertaken at different elevation angles (open, partially blocked and extremely blocked) and by considering three different correction techniques (FKP, VRS and MAC), and the results were evaluated in terms of repeatability. From the analysis of the data, it was understood that the performances of the three correction techniques were generally similar, and even in the case of a limited satellite view, the errors remained below 7 cm in all three techniques. However, when the 2D and 3D components were analyzed together, VRS technique showed better results than the other two techniques.
Skyscrapers cause both limited sky-view and multipath error when using Global Navigation Satellite System (GNSS) measurements for monitoring structural movements. To reduce multipath errors, cutoff elevation angle can be set to a high value such as 30 À40. However, in the case of employing high cutoff elevation angles, the use of GPS only may not provide adequate positioning solutions. To overcome this problem, Galileo and GLONASS observations are combined with GPS observations. This study experimentally investigates the contribution of multi-GNSS for studying the effects of different cutoff elevation angles on the accuracy of high-rate GNSS results for detecting characteristics of dynamic motions for structural health monitoring (SHM). The filtration design, noise level and Signal-to-Noise Ratio (SNR) of high-rate GNSS measurements of GPS-only, GPS/Galileo, GPS/ GLONASS and GPS/GLONASS/Galileo are assessed for different cutoff elevation angles. The results demonstrate that the SNR of GNSS solutions for GPS/GLONASS and GPS/GLONASS/Galileo is the highest, which signifies their use in SHM. The accuracy of the dynamic movements of structures can be attained to 2 mm, on average, using multi-GNSS measurements even when using high cutoff elevation angles up to 40. The precision of GPS/GLONASS and GPS/GLONASS/Galileo systems with different cutoff elevation angles was high when referenced to LVDT.
PPP (Precise Point Positioning-Hassas Nokta Konumlama) yöntemi ile hem statik hem de kinematik modda tek GNSS (Global Navigation Satellite Systems) alıcısı ile bağıl (rölatif) konum belirleme yöntemine oldukça yakın bir seviyede konum bilgisi elde edilebilmektedir. Bu yöntem hem maliyet hem de oldukça kolay uygulanması sebebi ile beklenen doğruluk ve hassasiyeti karşılaması durumunda bağıl konum belirleme yöntemine bir alternatif olarak kullanılmaya başlanmıştır. Bu çalışmada, Antarktika Yarımadasında bulunan Livingston Island' da bir Zodyak botu ile iki farklı günde bir dizi GNSS ölmeleri yapılmış ve GNSS verileri; bağıl yöntem, PPP-AR (Ambiguity Resolution) ve Geleneksel PPP yöntemleriyle ayrı ayrı değerlendirilmiştir. PPP-AR ve Geleneksel PPP yöntemlerinin kinematik konum belirleme performansı bağıl yöntemle karşılaştırılmıştır. Sonuçlar PPP-AR yönteminin üstünlüğünü açıkça göstermektedir.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.