Ultraprecise mirror devices show considerable potential with view to applications in the visible and the ultraviolet spectral ranges. Aluminum alloys gather good mechanical and excellent optical properties and thus they emerge as important mirror construction materials. However, ultraprecision machining and polishing of optical aluminum surfaces are challenging, which originates from the high chemical reactivity and the heterogeneous matrix structure. Recently, several ion beam-based techniques have been developed to qualify aluminum mirrors for short-wavelength applications. We give an overview of the state-of-the-art ion beamprocessing techniques for figure error correction and planarization, either by direct aluminum machining or with the aid of polymer or inorganic, amorphous surface films.
Aluminum mirrors offer great potential for satisfying the increasing demand in high-performance optical components for visible and ultraviolet applications. Ion beam figuring is an established finishing technology and in particular a promising technique for direct aluminum figure error correction. For the machining of strongly curved or arbitrarily shaped surfaces as well as the correction of low-to-mid spatial frequency figure errors, the usage of a high-performance ion beam source with low tool width is mandatory. For that reason, two different concepts of ion beam generation with high ion current density and narrow beam width are discussed. (1) A concave ion beam extraction grid system is used for apertureless constriction of ion beams in the low millimeter range. An oxygen ion beam with a full-width at half-maximum (FWHM) of 4.0 mm with an ion current density of 29.8 mA∕cm 2 was achieved.(2) For even smaller ion beams, a conic aperture design with a submillimeter-sized exit opening was tested. A nitrogen ion beam with an FWHM down to 0.62 mm with an ion current density of 4.6 mA∕cm 2 was obtained. In situ ion current density mapping is performed by scanning Faraday probe measurements. Special interest is set on the data evaluation for submillimeter ion beam analysis. © The Authors. Published by SPIE under a Creative Commons Attribution 3.0 Unported License. Distribution or reproduction of this work in whole or in part requires full attribution of the original publication, including its DOI.
For fabrication of high-performance mirror devices, technical aluminum alloys Al6061 or Al905 are widely used. The surface error topography after manufacturing by singlepoint diamond turning is applicable in the infrared spectral range. For increasing demands on the optical surface quality in the shortwave visible and ultraviolet spectral range, further improvement of the surface roughness is required. Hence, a promising alternative process to attain the required surface quality is evaluated. Within the ion beam planarization technique, a photoresist layer is deposited by conventional spin coating or spray coating technologies exhibiting an ultrasmooth surface. When removing the resist by reactive ion beam etch (RIBE) processing using nitrogen process gas, the ultrasmooth surface topography of the resist is transferred into the substrate. We optimized the photoresist thermal pretreatment to realize roughness preservation and a steady-state material removal rate during RIBE machining. The optimum preparation steps are explored based on roughness evaluation, chemical modification, and etch resistance of the negative photoresist. Reactive ion beam etching-based planarization is conducted on single-point diamond turned RSA Al905 and RSA Al6061 samples made of rapidly solidified aluminum (RSA) in a two-step process. The optimum process and the roughness evaluation are explored by topographic analysis applying a combination of white light interferometry and atomic force microscopy measurements. © The Authors. Published by SPIE under a Creative Commons Attribution 4.0 Unported License. Distribution or reproduction of this work in whole or in part requires full attribution of the original publication, including its DOI.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.