No abstract

The aim of this study was to examine the edentulism rates in Brazil and make projections for the next years. Data were collected from three national oral health surveys. The percentage of edentulous jaws was calculated. Projections were made for the years 2020, 2030 and 2040, assuming that edentulism follows a logistic function. Population projections were also performed. Annual change in proportion of edentulous jaws was -0.04% for teenagers, -0.96% for adults and 0.76% for the elderly. By 2040, edentulous jaws will be virtually zero among teenagers, 1.77% among adults and 85.96% among the elderly. Teenagers will slightly decrease in number; adults will increase and subsequently decrease; the elderly will continue to increase. In teenagers and adults, the number of edentulous jaws will decrease, being approximately 616,000 in 2040. In the elderly, it will increase alarmingly, reaching over 64 million in 2040. Edentulism is declining in Brazil among teenagers and middle-aged adults, but is still increasing and will continue to increase for the next decades among the elderly.

Removal torque values tended to decrease as the number of insertion/removal cycles increased, for both groups. Comparisons of the slopes and the intercepts between groups showed no statistical difference. There was no significant difference between the mean values of last five cycles and the 11th cycle. Within the limitations of this in vitro study, it was concluded that (1) repeated insertion/removal cycles promoted gradual reduction in removal torque of screws, (2) replacing the screw with a new one after 10 cycles did not increase resistance to loosening, and (3) removal of the hexagon from the abutment base had no effect on the removal torque of the screws.

Objective The purpose of this study was to assess the influence of conditioning methods and thermocycling on the bond strength between composite core and resin cement.Material and Methods Eighty blocks (8×8×4 mm) were prepared with core build-up composite. The cementation surface was roughened with 120-grit carbide paper and the blocks were thermocycled (5,000 cycles, between 5°C and 55°C, with a 30 s dwell time in each bath). A layer of temporary luting agent was applied. After 24 h, the layer was removed, and the blocks were divided into five groups, according to surface treatment: (NT) No treatment (control); (SP) Grinding with 120-grit carbide paper; (AC) Etching with 37% phosphoric acid; (SC) Sandblasting with 30 mm SiO2 particles, silane application; (AO) Sandblasting with 50 mm Al2O3 particles, silane application. Two composite blocks were cemented to each other (n=8) and sectioned into sticks. Half of the specimens from each block were immediately tested for microtensile bond strength (µTBS), while the other half was subjected to storage for 6 months, thermocycling (12,000 cycles, between 5°C and 55°C, with a dwell time of 30 s in each bath) and µTBS test in a mechanical testing machine. Bond strength data were analyzed by repeated measures two-way ANOVA and Tukey test (α=0.05).Results The µTBS was significantly affected by surface treatment (p=0.007) and thermocycling (p=0.000). Before aging, the SP group presented higher bond strength when compared to NT and AC groups, whereas all the other groups were statistically similar. After aging, all the groups were statistically similar. SP submitted to thermocycling showed lower bond strength than SP without thermocycling.Conclusion Core composites should be roughened with a diamond bur before the luting process. Thermocycling tends to reduce the bond strength between composite and resin cement.

Introduction: Marginal discrepancies may lead to cement washout and marginal leakage, damaging periodontal and pulp tissues or causing premature loss of the restoration. Purpose: This study evaluated the influence of application site of provisional cement on the marginal adaptation of provisional crowns. Material and Methods: Four different application sites of provisional cement (Temp Bond NE, Kerr Corporation) were used for cementation of provisional crowns on phantom teeth prepared for full crown restorations, performing 4 experimental groups (n=10): cement applied to all internal surfaces of the crown (CAO); cement applied to all internal surfaces of the crown, except for the occlusal surface (CA); cement applied to the cervical crown margin (CM); and cement applied to the cervical tooth margin (TM). A comparison microscope (Mitutoyo America Corporation) was used to measure the distances between the internal tangents of two circular marks, one made on the provisional crown and one made apical to the tooth preparation margin, in areas corresponding to buccal, lingual, mesial and distal surfaces. Marginal adaptation was determined before and after cementation, with 0.0001-mm accuracy. Data were analyzed statistically by ANOVA and Tukey's test at 5% significance level. Results: Mean values of marginal opening obtained for each group were: CAO: 145 μm; CA: 67 μm; CM: 46 μm; TM: 34 μm. CA, CM and TM presented significantly lower marginal openings than CAO (p<0.05). Conclusion: complete filling of the crown with provisional cement, including the occlusal surface, provided grater marginal discrepancies when compared to the other methods evaluated.

ObjectivesPrevious studies that evaluated the torque needed for removing dental implant screws have not considered the manner of transfer of the occlusal loads in clinical settings. Instead, the torque used for removal was applied directly to the screw, and most of them omitted the possibility that the hexagon could limit the action of the occlusal load in the loosening of the screws. The present study proposes a method for evaluating the screw removal torque in an anti-rotational device independent way, creating an unscrewing load transfer to the entire assembly, not only to the screw.Material and methodsTwenty hexagonal abutments without the hexagon in their bases were fixed with a screw to 20 dental implants. They were divided into two groups: Group 1 used titanium screws and Group 2 used titanium screws covered with a solid lubricant. A torque of 32 Ncm was applied to the screw and then a custom-made wrench was used for rotating the abutment counterclockwise, to loosen the screw. A digital torque meter recorded the torque required to loosen the abutment.ResultsThere was a significant difference between the means of Group 1 (38.62±6.43 Ncm) and Group 2 (48.47±5.04 Ncm), with p=0.001.ConclusionThis methodology was effective in comparing unscrewing torque values of the implant-abutment junction even with a limited sample size. It confirmed a previously shown significant difference between two types of screws.

IH implants show a higher frequency of bacterial leakage; and DLC and Ag-DLC films do not significantly reduce the frequency of bacterial leakage and bacteria load inside the implants.

No abstract