We report the fabrication of broadband directional couplers by direct UV-writing. The fabrication process is shown to be beneficial, robust and flexible. The components are compact and show superior performance in terms of loss and broadband operation.

A fiber Bragg grating (FBG) vibroacoustic sensor exploiting an intensity-based interrogation principle is presented. The optical system is complemented by signal processing techniques that allow disturbances to be mitigated and improve the spectral estimation. The sensor is capable of performing frequency analysis of sounds up to 3 kHz, with top sensitivity in the 100-500 Hz frequency range, and of dynamically tracking pulsed phenomena that induce a strain to the FBG. The sensor has been applied to the detection of voice, showing a great intelligibility of the speech despite the low-quality environment, and to the monitoring of the heartbeat rate from the wrist.

This paper reports on an epoxy matrix for glass fibre reinforced polymers equipped with low cost optical fibre sensors for the early detection of water diffusion, with devised applications in the oil and gas industry. Novel evanescent wave optical fibre sensors were designed, fabricated and embedded in epoxy resin samples. The tips of the optical fibre sensors were coated with a silver layer to work in reflection, so that they could be used as probes. Accelerated diffusion tests were performed: the samples were exposed to simulated sea water at 80 °C for up to 148 hours. The water diffusion resulted in a remarkable change of the reflected signal from the sensors, a result that was then confirmed through gravimetric measurements and a theoretical prediction, according to Fick's diffusion law. The results corroborate the feasibility of "sensitive" fibre reinforced polymers in harsh environments and that chemicals diffusion in these materials can be remotely and continuously monitored by means of the presented sensing system.

No abstract

The paper analyzes the performance of a dualwavelength technique devised to compensate power fluctuations in intensity-modulated plastic optical fiber sensors, which were specifically conceived for the measurement of displacements in industrial and civil applications. These sensors retrieve the displacement from the variation of the attenuation along the light path and use two signals at different wavelengths to compensate for the effects of parasitic quantities, such as temperature and strains along the fiber. The theoretical behavior of the compensation technique is presented and the results of experiments carried out with different combinations of signal wavelengths and plastic fibers are reported. The experimental setup has proved that, by proper choice of the compensation signal wavelength, it is possible to monitor displacements in the range (0 to 10) mm, even for low received power and under severe perturbation conditions, thus significantly improving the long-term stability of the sensors.

The design and fabrication of a tellurite glass multimode optical fiber for magneto-optical applications are presented and discussed. The analysis of the polarization shows that an optical beam, linearly polarized at the fiber input, changes to elliptically polarized with an ellipticity of 1∶4.5 after propagating down the fiber. However, the elliptical distribution remains unchanged with or without an applied magnetic field, demonstrating that no circular dichroism occurs within the fiber. The Verdet constant of the tellurite glass in the fiber is measured to be 28±0.5  rad·(T·m)-1, diverging by less than 3% from the Verdet constant found on the same glass composition in bulk form. These results demonstrate the feasibility to develop reliable tellurite glass fibers by the preform drawing method for magneto-optical applications.

Abstract-In this paper, we propose a spectral correlation-based technique for tracking the wavelength shift of a fiber Bragg grating. We compared this approach, by means of a Monte Carlo numerical simulation, to the typical peak tracking techniques applied in classic interrogation systems. As result, we obtained a considerable gain in terms of noise tolerance (about 20 dB), which can be further incremented by selecting large-bandwidth gratings. This permits to increase the power budget of a fiber Bragg grating interrogator without changing the optical layout, overcoming classical limitations of commercial and custom systems. Penalties due to the non-idealities have been evaluated through the same Monte Carlo approach. Finally, we discuss a practical application of the peak tracking techniques to a fiber Bragg grating-based weight sensor, in which we applied the spectral correlation to track both the Bragg wavelength position, spectral deformations due to high strain, and spectral non-linearity. Within the last few years, many commercial interrogators have converged to similar optical and processing architectures, most of them based on the straightforward and reliable principle of operation of spectral reconstruction; interrogators measure the wavelength shift of a FBG array simply by scanning a spectral bandwidth with a tunable laser, a tunable filter, or a spectrometer. In this case, a technique for evaluating the peak wavelength from the measured spectrum has to be implemented; typical interrogators define the peak wavelength either as the wavelength correspondent to the spectral 253 maximum or as the middle point of the X-dB bandwidth (usually 3 dB for weak gratings and 10 dB for strong gratings). Index Terms-A spectral correlation technique, however, permits improving performances of the Bragg wavelength tracking, for all spectrometric and spectral scan-based FBG interrogators, which represent the vast majority of commercial FBG sensing instruments [12]. The correlation method computes the mutual correlation between the reference spectrum and the measured one progressively shifted, and evaluates the FBG wavelength shift as the maximum of the correlation. We performed a Monte Carlo statistical simulation in order to compare the behavior of all peak tracking techniques, using the theoretical expressions of the FBG spectra and reproducing a typical FBG interrogation system, with the purpose of finding the minimum signal-to-noise ratio (SNR) that assesses a correct detection. As result from our simulation, we demonstrate that a FBG interrogator based on spectral reconstruction is capable of gaining a power budget of about 20 dB only by replacing the peak tracking algorithm, and this margin can be even increased by proper choice of the FBGs. Also, the Monte Carlo technique return quantitative results for FBG design, whereas the optimization of the FBG profile can lead to superior performance in peak tracking.Finally, peak tracking techniques have been compared in an applicative context of FBG sensor, validating t...

Abstract:The first demonstration of UV-written, silica-on-silicon integrated optical 1×N power splitters with up to 32 outputs ports is presented. The fabricated components exhibit 450 nm bandwidth, low excess loss and good channel uniformity.