The fundamental building blocks of digital electronics are logic gates which must be capable of cascading such that more complex logic functions can be realized. Here we demonstrate integrated graphene complementary inverters which operate with the same input and output voltage logic levels, thus allowing cascading. We obtain signal matching under ambient conditions with inverters fabricated from wafer-scale graphene grown by chemical vapor deposition (CVD). Monolayer graphene was incorporated in self-aligned field-effect transistors in which the top gate overlaps with the source and drain contacts. This results in full-channel gating and leads to the highest low-frequency voltage gain reported so far in top-gated CVD graphene devices operating in air ambient, A(v) ∼ -5. Such gain enabled logic inverters with the same voltage swing of 0.56 V at their input and output. Graphene inverters could find their way in realistic applications where high-speed operation is desired but power dissipation is not a concern, similar to emitter-coupled logic.

Ring oscillators (ROs) are the most important class of circuits used to evaluate the performance limits of any digital technology. However, ROs based on low-dimensional nanomaterials (e.g., 1-D nanotubes, nanowires, 2-D MoS2) have so far exhibited limited performance due to low current drive or large parasitics. Here we demonstrate integrated ROs fabricated from wafer-scale graphene grown by chemical vapor deposition. The highest oscillation frequency was 1.28 GHz, while the largest output voltage swing was 0.57 V. Both values remain limited by parasitic capacitances in the circuit rather than intrinsic properties of the graphene transistor components, suggesting further improvements are possible. The fabricated ROs are the fastest realized in any low-dimensional nanomaterial to date and also the least sensitive to fluctuations in the supply voltage. They represent the first integrated graphene oscillators of any kind and can also be used in a wide range of applications in analog electronics. As a demonstration, we also realized the first stand-alone graphene mixers that do not require external oscillators for frequency conversion. The first gigahertz multitransistor graphene integrated circuits demonstrated here pave the way for application of graphene in high-speed digital and analog circuits in which high operating speed could be traded off against power consumption.

A graphene audio voltage amplifier is fabricated by overlapping the gate with source/drain contacts. The fabricated complementary amplifier has a voltage gain of 3.7 (11.4 dB) at 10 kHz, a total harmonic distortion in the audio frequency range of <1%, a unity-gain frequency of 360 kHz, and a −3 dB bandwidth of 70 kHz

Abstract-We measure top-gated graphene field effect transistors (GFETs) with nanosecond-range pulsed gate and drain voltages. Due to high-κ dielectric or graphene imperfections, the drain current decreases ~10% over time scales of ~10 μs, consistent with charge trapping mechanisms. Pulsed operation leads to hysteresis-free I-V characteristics, which are studied with pulses as short as 75 ns and 150 ns at the drain and gate, respectively. The pulsed operation enables reliable extraction of GFET intrinsic transconductance and mobility values independent of sweep direction, which are up to a factor of two higher than those obtained from simple DC characterization. We also observe drain-bias-induced charge trapping effects at lateral fields greater than 0.1 V/µm. In addition, using modeling and capacitancevoltage measurements we extract charge trap densities up to 10 12 cm -2 in the top gate dielectric (here Al2O3). Our study illustrates important time-and field-dependent imperfections of top-gated GFETs with high-κ dielectrics, which must be carefully considered for future developments of this technology.

2D crystals, such as graphene, exhibit the higher strength and stiffness of any other known man-made or natural material. So far, this assertion has been primarily based on modelling predictions and on bending experiments in combination with pertinent modelling. True uniaxial loading of suspended graphene is not easy to accomplish; however such an experiment is of paramount importance in order to assess the intrinsic properties of graphene without the influence of an underlying substrate. In this work we report on uniaxial tension of graphene up to moderate strains of ∼0.8%. This has been made possible by sandwiching the graphene flake between two polymethylmethacrylate (PMMA) layers and by suspending its central part by the removal of a section of PMMA with e-beam lithography. True uniaxial deformation is confirmed by the measured large phonon shifts with strain by Raman spectroscopy and the indication of lateral buckling (similar to what is observed for thin macroscopic membranes under tension). Finally, we also report on how the stress is transferred to the suspended specimen through the adhesive grips and determine the value of interfacial shear stress that is required for efficient axial loading in such a system.