To improve the reactivity of lignin for incorporation into high value polymers, the introduction of amines via Mannich reaction is a commonly used strategy. During this functionalization reaction, intra- as well as intermolecular lignin–lignin crosslinking occurs, which can vastly change the elastic properties of the lignin, and therefore, the properties of the resulting polymer. Therefore, the molecular structure of the amine that is used for such a lignin functionalization may be of great importance. However, the relationship between the molecular structure of the amine and the elastic properties of the lignin-based polymer that is generated thereof, has not been fully understood. Herein, this relationship was investigated in detail and it was observed that the molecular flexibility of the amines plays a predominant role: The use of more flexible amines results in an increase in elasticity and the use of less flexible amines yields more rigid resin material. In addition to the macroscopic 3-point bending flexural tests, the elastic modules of the resins were determined on the nanometer scale by using atomic force microscopy (AFM) in the PeakForce tapping modus. Thus, it could be demonstrated that the intrinsic elasticities of the lignin domains are the main reason for the observed tendency.

Quinone-containing materials have attracted significant attention for energy storage and electroswing carbon capture. Tailored redox-responsive core−shell particles are obtained in the present work via semicontinuous starved-feed emulsion polymerization and subsequent postmodification strategies with redox-responsive quinone moieties. The use of glycidyl methacrylate within the shell material offers the possibility of a ring-opening reaction with the redox-responsive 2-aminoanthraquinone (2-AAQ), which possesses a high affinity toward electrophilic carbon dioxide. The successful preparation of monodisperse particles, an essential prerequisite for colloidal selfassembly, was investigated by dynamic light scattering and transmission electron microscopy. The presence of reactive epoxy functionalities was achieved by the ring-opening reaction with the Preussmann reagent. Postsynthesis modification was investigated using X-ray photoelectron spectroscopy and cyclic voltammetry measurements. The redox-responsive core−shell particles were subjected to the melt-shear organization technique to prepare freestanding opal films featuring structural colors. The monodisperse 2-AAQ-containing particles were investigated for self-assembly inside conductive carbon felts, and their electrochemically mediated carbon capture capabilities were studied.

Opal films with their vivid structural colors represent a field of tremendous interest and obtained materials offer the possibility for many applications, such as optical sensors or anti-counterfeiting materials. A convenient method for the generation of opal structures relies on the tailored design of core-interlayer-shell (CIS) particles. Within the present study, elastomeric opal films were combined with stimuli-responsive photoacids to further influence the optical properties of structurally colored materials. Starting from cross-linked polystyrene (PS) core particles featuring a hydroxy-rich and polar soft shell, opal films were prepared by application of the melt-shear organization technique. The photoacid tris(2,2,2-trifluoroethyl) 8-hydroxypyrene-1,3,6-trisulfonate (TFEHTS) could be conveniently incorporated during freeze-drying the particle dispersion and prior to the melt-shear organization. Furthermore, the polar opal matrix featuring hydroxylic moieties enabled excited-state proton transfer (ESPT), which is proved by spectroscopic evaluation. Finally, the influence of the photoacid on the optical properties of the 3-dimensional colloidal crystals were investigated within different experimental conditions. The angle dependence of the emission spectra unambiguously shows the selective suppression of the photoacid’s fluorescence in its deprotonated state.

The development of magnetic hybrid films containing diblock copolymers (DBCs) and magnetic nanoparticles (NPs) by printing is a highly promising method for scalable and low-cost fabrication. During printing, the drying and arrangement kinetics of the DBC and magnetic NPs play an important role in the film formation concerning morphology and magnetic properties. In this study, the morphology evolution of ultrahigh molecular weight DBC polystyrene-block-poly(methyl methacrylate) and magnetic iron platinum (FePt) NPs is investigated with grazing-incidence small-angle X-ray scattering (GISAXS) in situ during printing. For comparison, a pure DBC film is printed without FePt NPs under the same conditions. The GISAXS data suggest that the addition of NPs accelerates the solvent evaporation, leading to a faster film formation of the hybrid film compared to the pure film. As the solvent is almost evaporated, a metastable state is observed in both films. Compared with the pure film, such a metastable state continues longer during the printing process of the hybrid film because of the presence of FePt NPs, which inhibits the reorganization of the DBC chains. Moreover, investigations of the field-dependent magnetization and temperature-dependent susceptibility indicate that the printed hybrid film is superparamagnetic, which makes this film class promising for magnetic sensors.

The fabrication of nanocomposites containing magnetic nanoparticles is gaining interest as a model for application in small electronic devices. The self-assembly of block copolymers (BCPs) makes these materials ideal for use as a soft matrix to support the structural ordering of the nanoparticles. In this work, a high-molecular-weight polystyrene-b-poly(methyl methacrylate) block copolymer (PS-b-PMMA) was synthesized through anionic polymerization. The influence of the addition of different ratios of PMMA-coated FePt nanoparticles (NPs) on the self-assembled morphology was investigated using transmission electron microscopy (TEM) and small-angle X-ray scattering (SAXS). The self-assembly of the NPs inside the PMMA phase at low particle concentrations was analyzed statistically, and the negative effect of higher particle ratios on the lamellar BCP morphology became visible. The placement of the NPs inside the PMMA phase was also compared to theoretical descriptions. The magnetic addressability of the FePt nanoparticles inside the nanocomposite films was finally analyzed using bimodal magnetic force microscopy and proved the magnetic nature of the nanoparticles inside the microphase-separated BCP films.