RESUMO -O objetivo deste trabalho foi avaliar as propriedades físicas e mecânicas de painéis OSB produzidos com adesivos comerciais e tânico de Stryphnodendron adstringens (Mart.) Coville. Os adesivos comerciais ureia formaldeído (UF), fenol formaldeído (FF) e os taninos da Acacia mearnsi foram obtidos por doação por respectivas empresas produtoras, enquanto que o tanino de barbatimão foi obtido em laboratório. Todos adesivos tiveram as propriedades dos adesivos determinadas. Foram produzidos painéis OSB com os adesivos ureia-formaldeído, fenol-formaldeído, tanino-formaldeído a partir da acácia e do barbatimão. Os painéis foram produzidos com partículas do tipo strand, geradas a partir da madeira de pinus, com teor de adesivo de 8% a uma pressão de 40 kgf.cm -², um tempo e temperatura de prensagem de 8 min e 160°C, respectivamente. Em todas as propriedades avaliadas, o desempenho dos painéis produzidos com adesivo tânico de barbatimão foi melhor quando comparado com o dos painéis produzidos com o adesivo tânico de acácia. Os painéis produzidos com os adesivos UF, FF e tânico de barbatimão atenderam a todos os prerrequisitos estipulados pela norma de comercialização. Tal fato demonstra grande potencial de utilização dos taninos de barbatimão para produção de painéis OSB.Palavras-chave: Taninos; Adesivos naturais; Oriented strand board. OSB PANELS PERFORMANCE WITH COMMERCIAL ADHESIVES AND TANNIC ADHESIVE FROM BARBATIMÃOABSTRACT -The aim of this study was to evaluate the physical and mechanical properties of OSB (Oriented Strand Board) panels produced with commercial adhesives and tannic adhesive from Stryphnodendron adstringens (Mart.) Coville. The commercial adhesives, urea formaldehyde (UF), phenol formaldehyde (FF) and Acacia mearnsi tannin were obtained by donation by respective manufacturing companies, while the tannins of barbatimao were obtained in the laboratory. The adhesives had the adhesives properties determined. OSB panels were produced, with the adhesives urea-formaldehyde, phenol-formaldehyde, tannin-formaldehyde from Acacia and Stryphnodendron. The panels were produced with strand particles generated from pine wood with an adhesive content of 8% at a 40 kgf.cm -² of pressure, a time and pressing temperature of 8 minutes and 160°C, respectively. In all of the properties evaluated, the performance of the panels made with tannic adhesive from barbatimão was better when compared to panels manufactured with the tannic adhesive from acacia. The panels produced with urea-formaldehyde, phenol-formaldehyde and tannic adhesive of barbatimão met all requirements stipulated by the marketing standard. Fact that shows great use potential for tannin of barbatimão for OSB panels production.
Tannins from Myrcia splendens from the Amazon rainforest were used for the first time in the formulation of a urea-tannin-formaldehyde (UTF) resin. The objective was to evaluate the effect of different tannin proportions on the glue line performance in Pinus sp. woods, glued with UTF adhesive. The tannins were extracted in a water bath, using 1500 mL of water and 100g of dry bark (liquor/bark 15:1), with addition of 3% Na2SO3, at a temperature of 70 °C for three hours. The adhesives formulations were based on the gradual replacement of mass of the urea-formaldehyde (UF) adhesive by tannin powder, totalizing four compositions and one control treatment. UTF adhesives were evaluated for their physicochemical properties, shear bond strength (wet and dry) and wood failure. The addition of M. splendens tannins to the urea formaldehyde adhesive promoted an increase in glue line strength. The proportion of 5.0% of tannins proved to be ideal in the formulation of the UTF adhesive, considering all the parameters evaluated. Thus, this study proves the potential use of Amazonian tannins from Myrcia splendens in the partial composition of more sustainable UTF adhesives.
A segurança do trabalho é importante em todas as atividades, pois a falta de ações para prevenir e diminuir os acidentes causam prejuízos para o trabalhador afastado e para a produção da empresa. Em fábricas de móveis e marcenarias onde existe o processamento mecânico com diferentes tipos de máquinas e diversidade de madeiras a realidade não é diferente. Os elevados níveis de pressão sonora emitido pelas máquinas está relacionado com doenças de perda auditiva induzida pelo ruído (PAIR). Dessa forma o objetivo deste trabalho foi realizar um levantamento dos níveis de ruído contínuo/intermitente de fábricas de móveis no Brasil. O trabalho foi realizado por meio de buscas na literatura utilizando metodologia sistemática, seleção e extração das informações relevantes. Todos os valores de nível de ruído e dose nos trabalhos pesquisados ficaram acima do permitido por lei. Assim, podendo caracterizar os ambientes estudados como insalubres ao ruído e com risco iminente a saúde dos trabalhadores. Dessa forma, para evitar doenças, como a PAIR, é necessário o uso de medidas preventivas nos ambientes laborais e o uso de protetores auriculares.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.