Sodium montmorillonite nanoclay (Na+-MMT) was modified by plasma polymerization with methyl methacrylate (MMA) and styrene (St) as monomers and was denominated as Na+-MMT/MMA and Na+-MMT/St, respectively. This plasma modified nanoclay was used as reinforcement for polystyrene (PS) nanocomposites that were prepared by melt mixing. Pristine and modified Na+-MMT nanoclay were analyzed by the dispersion in various solvents, Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), and scanning electron microscopy (SEM). The results confirmed a change in hydrophilicity of the modified Na+-MMT, as well as the presence of a polymeric material over its surface. The pristine PS/Na+-MMT and modified PS/Na+-MMT/MMA and PS/Na+-MMT/St nanocomposites were studied with X-ray diffraction (XRD), differential scanning calorimetry (DSC), and TGA, as well as mechanical properties. It was found that the PS/Na+-MMT/St nanocomposites presented better thermal properties and an improvement in Young’s modulus (YM) in compared to PS/Na+-MMT/MMA nanocomposites.

In this study, the graphite effect on the mechanical and fire‐retardant performance of low‐density polyethylene (LDPE) and ethylene‐vinyl‐acetate (EVA) foam composites was investigated. Polymer composites were prepared by melt mixing process and foamed by hot press molding at different graphite content (0, 3, 6, and 12 phr). Cone calorimetric tests through heat release rate (HRR) curves obtained, revealed a decreasing of 45% on peak heat release rate (pHRR) of foam composites LDPE‐EVA with 12 phr of untreated graphite content compared than those LDPE‐EVA foamed composites without graphite, which was attributed to the good distribution of graphite in the composite and more residual generates as thermogravimetric analysis suggested. Mechanical properties of polymer foamed composites with high graphite content do not show significant detrimental as a result to the formation of more uniform cells with smaller size incorporating a material with high modulus like graphite. The results suggest that polymer foam composites with graphite are suitable for the building and construction industry, in sealing and thermal insulation applications with good fire‐retardant performance.

This article proposes a process to prepare fully bio-based elastomer nanocomposites based on polyfarnesene and cellulose nanocrystals (CNC). To improve the compatibility of cellulose with the hydrophobic matrix of polyfarnesene, the surface of CNC was modified via plasma-induced polymerization, at different powers of the plasma generator, using a trans-β-farnesene monomer in the plasma reactor. The characteristic features of plasma surface-modified CNC have been corroborated by spectroscopic (XPS) and microscopic (AFM) analyses. Moreover, the cellulose nanocrystals modified at 150 W have been selected to reinforce polyfarnesene-based nanocomposites, synthesized via an in-situ coordination polymerization using a neodymium-based catalytic system. The effect of the different loading content of nanocrystals on the polymerization behavior, as well as on the rheological aspects, was evaluated. The increase in the storage modulus with the incorporation of superficially modified nanocrystals was demonstrated by rheological measurements and these materials exhibited better properties than those containing pristine cellulose nanocrystals. Moreover, we elucidate that the viscoelastic moduli of the elastomer nanocomposites are aligned with power–law model systems with characteristic relaxation time scales similar to commercial nanocomposites, also implying tunable mechanical properties. In this foreground, our findings have important implications in the development of fully bio-based nanocomposites in close competition with the commercial stock, thereby producing alternatives in favor of sustainable materials.

This paper presents the development of a high voltage and high-frequency power electronics source, for plasma generation, at atmospheric pressure and vacuum, using helium and air as working gases. The source design consists of an inductive (L) full bridge series resonant inverter at high frequency, where the control implemented allows varying duty cycle and frequency. Plasma generation is made by high voltage with the power signal applied on two electrodes, which provides a strong electric field that excites, and thus, ionize helium particles or air particles. The power electronic source operation was tested in different plasma reactor configurations (dielectric barrier discharge, double dielectric barrier discharge, and jet type discharge). The developed power electronics source shows a correct performance and generate a strong electric field to achieve the plasma discharges desired.

Currently there is a great trend towards cleaner, more sustainable and green production, based on a circular economy. Therefore, in the present work the study of the effect of the concentration of potato starch, aloe vera and graphene on the mechanical properties, water vapor permeability, biodegradability and structural properties of bioplastics is reported. These bioplastics could replace conventional synthetic plastics that currently produce high environmental pollution. According to the statistical analysis of a 2 ˄ 3 factorial design, a biodegradable bioplastic with improved mechanical properties was obtained, with a high maximum stress of 2.49 ± 0.28 MPa at high concentration levels of starch, aloe vera and graphene (10% w/w starch, 24% w/w of aloe and 0.045% w/w of graphene). A minimum value of permeance and permeability to water vapor of 5.35 kg/h.kPa.m 2 and 0.001839 kg/h.kPa.m, respectively, was found at a graphene concentration of 0.005%; aloe concentration, 24%; and starch concentration, 10%.

This study aims to investigate the effect of ground tire rubber (GTR) treated by acetone on mechanical and morphological properties of ethylene-vinyl acetate (EVA) matrix. Polymeric EVA/GTR (0, 10, 20, 30, and 40 phr) compounds were achieved through extrusion and batch foaming process. TGA and NMR analysis revealed that oils and additives were removed from the GTR after the acetone treatment. Morphological characterization showed cell sizes below 100 μm in the compounds with treated GTR, which improved the mechanical performance of EVA/GTR compounds. The results indicated that the acetonetreated GTR are a suitable raw material to obtain foam compounds useful in vibrations absorber and isolation applications.