Carbon deposition following thermal methane decomposition under dry and steam reforming conditions has been studied on yttria-stabilized zirconia (YSZ), Y2O3, and ZrO2 by a range of different chemical, structural, and spectroscopic characterization techniques, including aberration-corrected electron microscopy, Raman spectroscopy, electric impedance spectroscopy, and volumetric adsorption techniques. Concordantly, all experimental techniques reveal the formation of a conducting layer of disordered nanocrystalline graphite covering the individual grains of the respective pure oxides after treatment in dry methane at temperatures T ≥ 1000 K. In addition, treatment under moist methane conditions causes additional formation of carbon-nanotube-like architectures by partial detachment of the graphite layers. All experiments show that during carbon growth, no substantial reduction of any of the oxides takes place. Our results, therefore, indicate that these pure oxides can act as efficient nonmetallic substrates for methane-induced growth of different carbon species with potentially important implications regarding their use in solid oxide fuel cells. Moreover, by comparing the three oxides, we could elucidate differences in the methane reactivities of the respective SOFC-relevant purely oxidic surfaces under typical SOFC operation conditions without the presence of metallic constituents.

Colorless single crystals, as well as polycrystalline samples of TiTa2O7 and TiNb2O7, were grown directly from the melt and prepared by solid-state reactions, respectively, at various temperatures between 1598 K and 1983 K. The chemical composition of the crystals was confirmed by wavelength-dispersive X-ray spectroscopy, and the crystal structures were determined using single-crystal X-ray diffraction. Structural investigations of the isostructural compounds resulted in the following basic crystallographic data: monoclinic symmetry, space group I2/m (No. 12), a = 17.6624(12) Å, b = 3.8012(3) Å, c = 11.8290(9) Å, β = 95.135(7)°, V = 790.99(10) Å(3) for TiTa2O7 and a = 17.6719(13) Å, b = 3.8006(2) Å, c = 11.8924(9) Å, β = 95.295(7)°, V = 795.33(10) Å(3), respectively, for TiNb2O7, Z = 6. Rietveld refinement analyses of the powder X-ray diffraction patterns and Raman spectroscopy were carried out to complement the structural investigations. In addition, in situ high-temperature powder X-ray diffraction experiments over the temperature range of 323-1323 K enabled the study of the thermal expansion tensors of TiTa2O7 and TiNb2O7. To determine the hardness (H), and elastic moduli (E) of the chemical compounds, nanoindentation experiments have been performed with a Berkovich diamond indenter tip. Analyses of the load-displacement curves resulted in a hardness of H = 9.0 ± 0.5 GPa and a reduced elastic modulus of Er = 170 ± 7 GPa for TiTa2O7. TiNb2O7 showed a slightly lower hardness of H = 8.7 ± 0.3 GPa and a reduced elastic modulus of Er = 159 ± 4 GPa. Spectroscopic ellipsometry of the polished specimens was employed for the determination of the optical constants n and k. TiNb2O7 as well as TiTa2O7 exhibit a very high average refractive index of nD = 2.37 and nD = 2.29, respectively, at λ = 589 nm, similar to that of diamond (nD = 2.42).

The surface reactivity of Y2O3, YSZ, and ZrO2 polycrystalline powder samples toward H2 has been comparatively studied by a pool of complementary experimental techniques, comprising volumetric methods (temperature-programmed volumetric adsorption/oxidation and thermal desorption spectrometry), spectroscopic techniques (in situ electric impedance and in situ Fourier-transform infrared spectroscopy), and eventually structural characterization methods (X-ray diffraction and scanning electron microscopy). Reduction has been observed on all three oxides to most likely follow a surface or near-surface-limited mechanism involving removal of surface OH-groups and associated formation of water without formation of a significant number of anionic oxygen vacancies. Partly reversible adsorption of H2 was proven on the basis of molecular H2 desorption. Dictated by the specific hydrophilicity of the oxide, readsorption of water eventually takes place. The inference of this surface-restricted mechanism is further corroborated by the fact that no bulk structural and/or morphological changes were observed upon reduction even at the highest reduction temperatures (1173 K). We anticipate relevant implications for the use of especially YSZ in fuel cell research, since in particular the chemical state and structure of the surface under typical reducing high-temperature conditions affects the operation of the entire cell.

The C1-surface chemistry of catalytically and technologically relevant oxides (YSZ, ZrO 2 and Y 2 O 3) towards CH 4 , CO and CO 2 was comparatively studied by electrochemical impedance (EIS) and spectroscopic (FT-IR) methods. Highly correlated in-situ measurements yield a consistent picture with respect to qualitative and quantitative surface modifications as a function of temperature and gas phase composition. This includes a detailed study of carbon deposition in methane and adsorption of CO and CO 2 , but also proof of the strong influence of surface chemistry. On all studied oxides, carbon deposited during methane treatment grows dynamically forming interconnected islands and eventually a continuous conducting carbon layer at T ≥ 1073 K. Before methane dissociation via gas phase radical reactions/H-abstraction and carbon growth, a complex redox interplay of total oxidation, formate and carbonate formation leads to associated surface and grain conductivity changes. For CO adsorption, these measurements yield data on the time-and temperature dependence of the adsorbate-and carburization-induced conductivity processes. In that respect, an equivalent circuit model in dry CO allows to disentangle the different contributions of grain interiors, grain boundaries and electrode contributions. For YSZ, temperature regions with different charge carrier activation energies could be identified, perfectly corresponding to significant changes in surface chemistry. Hydroxyl groups, carbonates or formates strongly influence the impedance properties, suggesting that the conductivity properties of YSZ e.g. in a realistic reforming gas mixture cannot be reduced to exclusive bulk ion conduction. Due to the different degree of hydroxylation and the different ability to chemisorb CO and CO 2 , the influence of the surface chemistry on the electrochemical properties is varying strongly: in contrast to ZrO 2 , the impact of the studied C1-gases on YSZ and Y 2 O 3 is substantial. This also includes the re-oxidation/re-activation behavior of the surfaces.

New actinide borates ThB4O8 and UB4O8 were synthesized under high‐pressure, high‐temperature conditions (5.5 GPa/1100 °C for thorium borate, 10.5 GPa/1100 °C for the isotypic uranium borate) in a Walker‐type multianvil apparatus from their corresponding actinide oxide and boron oxide. The crystal structure was determined on basis of single‐crystal X‐ray diffraction data that were collected at room temperature. Both compounds crystallized in the monoclinic space group C2/c (Z=4). Lattice parameters for ThB4O8: a=1611.3(3), b=419.86(8), c=730.6(2) pm; β=114.70(3)°; V=449.0(2) Å3; R1=0.0255, wR2=0.0653 (all data). Lattice parameters for UB4O8: a=1589.7(3), b=422.14(8), c=723.4(2) pm; β=114.13(3)°; V=443.1(2) Å3; R1=0.0227, wR2=0.0372 (all data). The new AnB4O8 (An=Th, U) structure type is constructed from corner‐sharing BO4 tetrahedra, which form layers in the bc plane. One of the four independent oxygen atoms is threefold‐coordinated. The actinide cations are located between the boron–oxygen layers. In addition to Raman spectroscopic investigations, DFT calculations were performed to support the assignment of the vibrational bands.