Mn-WO3/TiO2 catalysts were investigated for Selective Catalytic Reduction (SCR) of NO with NH3. The catalysts were synthesized by wetness impregnation method with different Mn loadings (1.5-3-12 wt%) on 8wt%WO3/TiO2. All three catalysts were compared with 8wt%WO3/TiO2 and bare MnOx oxide, used as references. The 1.5wt%Mn-8wt%WO3/TiO2 exhibited the highest performance in NO conversion and N2 selectivity. A commercial catalyst, based on titania supported vanadia and tungsta, (V2O5-WO3/TiO2), widely used for its high efficiency, was also investigated in the present work. The morphological, structural, redox and electronic properties of the catalysts and their thermal stability were studied by several techniques (N2 adsorption/desorption, X-ray diffraction, H2 temperature-programmed reduction, NH3 temperature programmed desorption, X-ray photoelectron spectroscopy).The aim of this paper is to study the effect of different Mn loadings on 8wt%WO3/TiO2 with the ambition to obtain highly active and selective catalysts in a large window of temperature. The replacement of toxic vanadium used in the classic V2O5-WO3/TiO2 catalyst with MnOx in the best performing catalyst, 1.5wt%Mn-8wt%WO3/TiO2, represents an important achievement to improve the environmental sustainability.
In the present study CeO2, MnO2 and CeMnOx mixed oxide (with molar ratio Ce/Mn = 1) were prepared by sol-gel method using citric acid as a chelating agent and calcined at 500 °C. The silver catalysts (1 wt% Ag) over the obtained supports were synthesized by the incipient wetness impregnation method with [Ag(NH3)2]NO3 aqueous solution. The selective catalytic reduction of NO by C3H6 was investigated in a fixed-bed quartz reactor using a reaction mixture composed of 1000 ppm NO, 3600 ppm C3H6, 10 vol.% O2, 2.9 vol.% H2 and He as a balance gas, at WHSV of 25,000 mL g−1 h−1.The physical-chemical properties of the as-prepared catalysts were studied by several characterization techniques, such as X-ray fluorescence analysis, nitrogen adsorption/desorption, X-ray analysis, Raman spectroscopy, transmission electron microscopy with analysis of the surface composition by X-ray energy dispersive spectroscopy and X-ray photo-electron spectroscopy. Silver oxidation state and its distribution on the catalysts surface as well as the support microstructure are the main factors determining the low temperature activity in NO selective catalytic reduction. The most active Ag/CeMnOx catalyst (NO conversion at 300 °C is 44% and N2 selectivity is ~ 90%) is characterized by the presence of the fluorite-type phase with high dispersion and distortion. The characteristic “patchwork” domain microstructure of the mixed oxide along with the presence of dispersed Ag+/Agnδ+ species improve the low-temperature catalyst of NO reduction by C3H6 performance compared to Ag/CeO2 and Ag/MnOx systems.
Novel yttrium-doped CeO2, MnOx, and CeMnOx composites are investigated as catalysts for low-temperature NH3-SCR. The study involves the preparation of unmodified oxide supports using a citrate method followed by modification with Y (2 wt.%) using two approaches, including the one-pot citrate method and incipient wetness impregnation of undoped oxides. The NH3-SCR reaction is studied in a fixed-bed quartz reactor to test the ability of the prepared catalysts in NO reduction. The gas reaction mixture consists of 800 ppm NO, 800 ppm NH3, 10 vol.% O2, and He as a balance gas at a WHSV of 25,000 mL g−1 h−1. The results indicate that undoped CeMnOx mixed oxide exhibits significantly higher deNOx performance compared with undoped and Y-doped MnOx and CeO2 catalysts. Indeed, yttrium presence in CeMnOx promotes the competitive NH3-SCO reaction, reducing the amount of NH3 available for NO reduction and lowering the catalyst activity. Furthermore, the physical-chemical properties of the prepared catalysts are studied using nitrogen adsorption/desorption, XRD, Raman spectroscopy, temperature-programmed reduction with hydrogen, and temperature-programmed desorption of ammonia. This study presents a promising approach to enhancing the performance of NH3-SCR catalysts at low temperatures that can have significant implications for reducing NO emissions.
Co/TiO2 catalysts with different cobalt loadings (3.8, 7.5 and 15 wt%) were prepared by impreg-nation method of Co(NO3)2 .6H2O over titania. Samples containing Co(NO3)2 .6H2O and TiO2 in stoichiometric proportions in order to obtain CoTiO3 and Co2 TiO4 phases were also synthesized. The effect of the calcination treatment at two different temperatures, 550 and 1150 °C was investigated. Characterizations by several techniques, such as XRD UV-vis-NIR, DRS, Raman and XPS were carried out. XRD showed the coexistence of three phases: CoTiO3; Co2TiO4 and Co3O4 after calci-nation at 550°C, while the calcination at high temperature (1150°C) leads to single-phase systems (CoTiO3 or Co2TiO4). Diffuse reflection and XPS spectroscopy showed that divalent cobalt occupies octahedral sites in the ilmenite phase and both tetrahedral and octahedral sites in the spinel phase. The catalytic performances of the prepared catalysts, calcined at the two different temperatures, were evaluated in the oxidative dehydrogenation reaction (ODH) of ethane to ethylene. The con-version values were almost comparable for all the samples, calcined at 550 °C, and comparable the ethylene selectivity were recorded, slightly higher only in the case of CoTiO3. The calcination at 1150°C did not modify the overall activity (ethane conversion values around 20%), however, the production of COx becomes more significant. The study examined the influence of the reaction mixture composition, specifically the presence of water, and reveals a slight increase in the yield of ethylene accompanied by a decrease in the overall catalyst activity. This behavior is likely attributed to an increase in the surface concentration of hydroxyl species (OH), resulting in heightened surface acidity.
The reaction of octakis(3-chloropropyl)octasilsesquioxane with four equivalents of 1-hexylimidazole or 1-decylimidazole gave two products labelled as HQ-POSS (hexyl-imidazolium quaternized POSS) and DQ-POSS (decyl-imidazolium quaternized POSS) as regioisomer mixtures. An investigation of the biological activity of these two compounds revealed the higher antimicrobial performances of HQ-POSS against Gram-positive and Gram-negative microorganisms, proving its broad-spectrum activity. Due to its very viscous nature, HQ-POSS was adsorbed in variable amounts on the surface of biologically active oxides to gain advantages regarding the expendability of such formulations from an applicative perspective. Titania and 5 wt% Cu on titania were used as supports. The materials 10HQ-POSS/Ti and 15HQ-POSS/5CuTi strongly inhibited the ability of Pseudomonas PS27 cells—a bacterial strain described for its ability to handle very toxic organic solvents and perfluorinated compounds—to grow as planktonic cells. Moreover, the best formulations (i.e., 10HQ-POSS/Ti and 15HQ-POSS/5CuTi) could prevent Pseudomonas PS27 biofilm formation at a certain concentration (250 μg mL−1) which greatly impaired bacterial planktonic growth. Specifically, 15HQ-POSS/5CuTi completely impaired cell adhesion, thus successfully prejudicing biofilm formation and proving its suitability as a potential antifouling agent. Considering that most studies deal with quaternary ammonium salts (QASs) with long alkyl chains (>10 carbon atoms), the results reported here on hexylimidazolium-based POSS further deepen the knowledge of QAS formulations which can be used as antifouling compounds.
Co/TiO2 catalysts with different cobalt loadings (3.8, 7.5 and 15 wt%) were prepared by impregnation method of Co(NO3)2 6H2O over titania. Samples containing Co(NO3)2·6H2O and TiO2 in stoichiometric proportions in order to obtain CoTiO3 and Co2 TiO4 phases were also synthesized. The effect of the calcination treatment at two different temperatures, 550 and 1150 °C, was investigated. Characterizations by several techniques, such as XRD, UV–vis–NIR, DRS, Raman and XPS, were carried out. XRD showed the coexistence of three phases: CoTiO3; Co2TiO4 and Co3O4 after calcination at 550 °C, while calcination at high temperature (1150 °C) led to single-phase systems (CoTiO3 or Co2TiO4). Diffuse reflection and XPS spectroscopy showed that divalent cobalt occupies octahedral sites in the ilmenite phase, and both tetrahedral and octahedral sites in the spinel phase. The catalytic performances of the prepared catalysts were evaluated in the oxidative dehydrogenation reaction (ODH) of ethane to ethylene, as a function of the Co content for Co/TiO2 catalysts and as a function of the calcination temperatures for the CoTiO3 and Co2TiO4 phases. Co(7.5)/TiO2 was the most active, although the conversion of ethane decreased in the first 150 min of the reaction, reaching values comparable to those of Co2TiO4 and CoTiO3; however, Co(7.5)/TiO2 was confirmed as having the best selectivity to ethylene in comparison with the bulk phases, CoTiO3 and Co2TiO4. The influence of the reaction mixture composition, specifically the presence of water, at different percentages, was investigated. There is a decrease in the overall ethane conversion and an increase in the ethylene selectivity when the percentage of water increases. This behavior can likely be attributed to an increase in the surface concentration of hydroxyl species (OH), resulting in heightened surface acidity.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.