Proteins in biological fluids (blood, urine, cerebrospinal fluid) are important biomarkers of various pathological conditions. Protein biomarkers detection and quantification have been proven to be an indispensable diagnostic tool in clinical practice. There is a growing tendency towards using portable diagnostic biosensor devices for point-of-care (POC) analysis based on microfluidic technology as an alternative to conventional laboratory protein assays. In contrast to universally accepted analytical methods involving protein labeling, label-free approaches often allow the development of biosensors with minimal requirements for sample preparation by omitting expensive labelling reagents. The aim of the present work is to review the variety of physical label-free techniques of protein detection and characterization which are suitable for application in micro-fluidic structures and analyze the technological and material aspects of label-free biosensors that implement these methods. The most widely used optical and impedance spectroscopy techniques: absorption, fluorescence, surface plasmon resonance, Raman scattering, and interferometry, as well as new trends in photonics are reviewed. The challenges of materials selection, surfaces tailoring in microfluidic structures, and enhancement of the sensitivity and miniaturization of biosensor systems are discussed. The review provides an overview for current advances and future trends in microfluidics integrated technologies for label-free protein biomarkers detection and discusses existing challenges and a way towards novel solutions.
Experimental studies were conducted on the effects of lead oxide on the microstructure and the ferroelectric properties of lead zirconate-titanate (PZT) films obtained by the method of radio frequency (RF) magnetron sputtering of a ceramic PZT target and PbO2 powder with subsequent heat treatment. It is shown that the change in ferroelectric properties of polycrystalline PZT films is attributable to their heterophase structure with impurities of lead oxide. It is also shown that, even in the original stoichiometric PZT film, under certain conditions (temperature above 580 °C, duration greater than 70 min), impurities of lead oxide may be formed. The presence of a sublayer of lead oxide leads to a denser formation of crystallization centers of the perovskite phase, resulting in a reduction of the grain size as well as the emergence of a charge on the lower interface. The formation of the perovskite structure under high-temperature annealing is accompanied by the diffusion of lead into the surface of the film. Also shown is the effect of the lead ions segregation on the formation of the self-polarized state of thin PZT films.
Microfluidic
devices for culturing cells have been successfully
utilized for biomedical applications, including drug screening. Several
cell lines could be cultivated in microengineered environments with
promising results, but gastric cell lines have not yet been widely
used or studied. Therefore, this study focuses on establishing a polarized
gastric epithelial monolayer on-a-chip and describes a general-purpose
methodology applicable for bonding any porous material to PDMS through
an adhesive sublayer. The fully transparent microfluidic chip consists
of two microfluidic channels separated by a collagen-coated porous
membrane and lined by human polarized gastric epithelial (NCI-N87)
cells. We present considerations on how to ensure continuous and stable
flow through the channels. The continuous flow rate was achieved using
a pressure-driven pump. Media flow at a constant rate (0.5 μL/min)
rapidly led the gastric epithelial cells to develop into a polarized
monolayer. The barrier integrity was assessed by the FITC-dextran
test. The generation of a monolayer was faster than in the static
Boyden chamber. Moreover, fluorescence microscopy was used to monitor
the apoptotic cell death of gastric epithelial monolayers on-a-chip
in response to camptothecin, a therapeutic gastric cancer drug.
Organ-on-a-chip devices are gaining popularity in medical research due to the possibility of performing extremely complex living-body-resembling research in vitro. For this reason, there is a substantial drive in developing technologies capable of producing such structures in a simple and, at the same time, flexible manner. One of the primary challenges in producing organ-on-chip devices from a manufacturing standpoint is the prevalence of layer-by-layer bonding techniques, which result in limitations relating to the applicable materials and geometries and limited repeatability. In this work, we present an improved approach, using three dimensional (3D) laser lithography for the direct integration of a functional part—the membrane—into a closed-channel system. We show that it allows the freely choice of the geometry of the membrane and its integration into a complete organ-on-a-chip system. Considerations relating to sample preparation, the writing process, and the final preparation for operation are given. Overall, we consider that the broader application of 3D laser lithography in organ-on-a-chip fabrication is the next logical step in this field’s evolution.
Zusammenfassung
Es ist von höchster wissenschaftlicher Relevanz, Biosensoren in Lab-on-Chip-Systeme zu integrieren. Die Integration der Sensoren in die Zellkultursysteme ermöglicht die direkte Messung der biologischen und physiologischen Parameter während des Zellwachstums. Es erfordert ein spezielles Design des mikrofluidischen Chips und eine Mikrostrukturierung der leitfähigen Materialien. In dieser Arbeit präsentieren wir zwei Ansätze für in-situ Messungen von physiologischen Parametern. Der erste ist eine Integration eines kommerziellen optischen Sensors für die Sauerstoffgehaltsdetektion und der zweite ist ein eigener, von uns entworfener und hergestellter transepithelialer Widerstandssensor (TEER) für Zellkonfluenzmessungen. Beide Sensoren wurden in einen flexiblen Mikrofluidik-Chip auf Basis von Polydimethylsiloxan (PDMS) integriert.
Desulfurization of hydrocarbons is an important step in the processing of petroleum products, which requires an accurate and robust method for the sulfur-containing component evaluation. On the other hand, sulfur-containing heteroatomic hydrocarbon additives are harmful for people and the environment. Therefore, it is advantageous to conduct laboratory tests at low volumes to reduce doses of exposure of sulfur-containing vapors to the personnel. Microfluidics is an emerging platform that provides an advantage to operate with low volumes. The microfluidic dielectric spectroscopy approach is proposed in the current contribution as a platform for determination of the concentration of polar heteroatomic components in binary mixtures. The presence of heteroatomic components in petroleum products leads to a perceptible change in the dielectric properties of the blend. This paper shows the technological aspects for the microfluidic sensor chip design. It was successfully used to determine the concentration of thiophene (as a typical sulfur-containing hydrocarbon) in gasoline. We compare the commercially available solution with the developed microfluidic sensor. We demonstrate the developed microfluidic sensor chip that has a comparable sensitivity as a macroscopic commercial measurement cell but at the microscale. It is able to operate at 103 times reduced volume of liquid analyte, providing stable control of the sulfur-containing additive concentration. The obtained results are intended to be applied for lab monitoring of sulfur-containing components in petroleum products.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.