We report the first synthesis of polyimide aerogels cross-linked through a polyhedral oligomeric silsesquioxane, octa(aminophenyl)silsesquioxane (OAPS). Gels formed from polyamic acid solutions of 3,3',4,4'-biphenyltetracarboxylic dianhydride (BPDA), bisaniline-p-xylidene (BAX) and OAPS were chemically imidized and dried using supercritical CO(2) extraction to give aerogels having density around 0.1 g/cm(3). The aerogels are greater than 90 % porous, have high surface areas (230 to 280 m(2)/g) and low thermal conductivity (14 mW/m-K at room temperature). Notably, the polyimide aerogels cross-linked with OAPS have higher modulus than polymer reinforced silica aerogels of similar density and can be fabricated as both monoliths and thin films. Thin films of the aerogel are flexible and foldable making them an ideal insulation for space suits, and inflatable structures for habitats or decelerators for planetary re-entry, as well as more down to earth applications.

Combinations of rigid and flexible aromatic diamines were used to tailor the properties of octa(aminophenyl)-silsesquioxane (OAPS) cross-linked polyimide aerogels. 2,2'-Dimethylbenzidine (DMBZ) or p-phenylenediamine (PPDA) was used in combination with the more-flexible diamine, 4,4'-oxydianiline (ODA). The amount of rigid diamine was varied from 0% to 100% of the total diamines in the backbone. The resulting aerogels vary in density, shrinkage, porosity, surface area, mechanical and thermal properties (depending on the type of diamine and the proportions of rigid diamine to flexible diamine used). Replacing ODA with PPDA increases shrinkage that occurs during gelation and processing, while increasing the DMBZ fraction decreases shrinkage. Replacing ODA with 50 mol% of DMBZ maintains the flexibility of thin films, while the moisture resistance of the aerogels is greatly improved.

Polyimide aerogels combine high porosity, low thermal conductivity, flexibility, and low density with excellent mechanical properties. However, previously used cross-linkers, such as 1,3,5-triaminophenoxybenzene (TAB), 2,4,6-tris(4-aminophenyl)pyridine (TAPP), or octa(aminophenoxy)silsesquioxane (OAPS), either are not commercially available or are prohibitively expensive. Finding more cost efficient cross-linkers that are commercially available to synthesize these aerogels is crucial for making large scale manufacturing attractive. Herein, we describe an approach to making polyimide aerogels starting with amine capped oligomers that are cross-linked with 1,3,5-benzenetricarbonyl trichloride (BTC). BTC is a lower cost, commercially available alternative to TAB, TAPP, or OAPS. Aerogels made in this way have the same or higher modulus and higher surface area compared to those previously reported with either TAB or OAPS cross-links at the same density. While the cross-link structure is an amide, the thermal stability is not compromised most likely because the cross-link is only a small part of the composition of the aerogel. Onset of decomposition depends primarily on the backbone chemistry with 4,4'-oxidianiline (ODA) being more thermally stable than 2,2'-dimethylbenzidine (DMBZ), similar to those previously reported with other cross-links.

No abstract

Structure-property relationships in porous 3-D nanostructures as a function of preparation conditions: isocyanate crosslinked silica aerogels Aerogels produced by cross-linking amine decorated silica surfaces with diisocyanates are significantly stronger than native aerogels with only a small effect on density or porosity. Herein, we examine the effects of four processing parameters on properties of resulting monoliths, focusing on 13 C NMR to give insight into the polymer cross-link. 2 have been shown to significantly increase the strength of aerogels with only a small effect on density or porosity. Though density is a prime predictor of properties such as strength and thermal conductivity for aerogels, it is becoming clear from previous studies that varying the silica backbone and size of the polymer cross-link independently can give rise to combinations of properties which cannot be predicted from density alone. Herein, we examine the effects of four processing parameters for producing this type of polymer cross-linked aerogel on properties of the resulting monoliths. We focus on the results of 13 C CP-MAS NMR which gives insight to the size and structure of polymer cross-link present in the monoliths, and relates the size of the cross-links to microstructure, mechanical properties and other characteristics of the materials obtained.

The effect of incorporating an organic linking group, 1,6-bis(trimethoxysilyl)hexane (BTMSH), into the underlying silica structure of a styrene cross-linked silica aerogel is examined. Vinyltrimethoxysilane (VTMS) is used to provide a reactive site on the silica backbone for styrene polymerization. Replacement of up to 88 mol % of the silicon from tetramethoxyorthosilicate with silicon derived from BTMSH and VTMS during the making of silica gels improves the elastic behavior in some formulations of the cross-linked aerogels, as evidenced by measurement of the recovered length after compression of samples to 25% strain. This is especially true for some higher density formulations, which recover nearly 100% of their length after compression to 25% strain twice. The compressive modulus of the more elastic monoliths ranged from 0.2 to 3 MPa. Although some of these monoliths had greatly reduced surface areas, changing the solvent used to produce the gels from methanol to ethanol increased the surface area in one instance from 6 to 220 m(2)/g with little affect on the modulus, elastic recovery, porosity, or density.

Cross-linking silica aerogels with organic groups has been shown to improve the strength over un-cross-linked aerogels by as much as 2 orders of magnitude. Previous cross-linking chemistry has been developed using solvents specifically chosen to dissolve the monomers and accommodate the reaction temperature. Because the process of making the aerogels requires so much solvent, it is of interest to consider less toxic solvents such as ethanol to increase safety and enhance scale up. To this end, two different epoxy precursors with suitable solubility in ethanol were evaluated as cross-linkers for silica gels prepared from (3-aminopropyl)triethoxysilane and tetraethylorthosilicate. In addition, 1,6-bis(trimethoxysilyl)hexane (BTMSH) was used as an additive in the underlying silica structure to add flexibility to the aerogels. It was found that the ethanol-derived aerogels exhibited more shrinkage than those prepared from other solvents but that including BTMSH in the aerogels significantly reduced this shrinkage. Inclusion of BTMSH also imparted the ability of the aerogel monoliths to recover elastically when compressed up to 50% strain. In addition, optimized cross-linked aerogels prepared in this study have mechanical properties comparable to those using other more undesirable solvents and cross-linkers.

We describe a three-dimensional core-shell structure where the core is the assembly of nanoparticles that comprises the skeletal framework of a typical silica aerogel, and the shell is polystyrene. Specifically, the mesoporous surfaces of silica were first modified with amines by co-gelation of tetramethylorthosilicate (TMOS) and 3-aminopropyltriethoxysilane (APTES). Next, styrene moieties were attached to the amines by reaction with p-chloromethylstyrene. Finally, dangling styrene moieties were crosslinked by a free-radical polymerization process initiated by AIBN and styrene, p-chloromethylstyrene or 2,3,4,5-pentafluorostyerene introduced in the mesopores. Polystyrene crosslinked aerogels are mechanically strong, lightweight (0.41-0.77 g cm 23 ), highly porous materials (they consist of ca. 63% empty space, with a BET surface areas in the range of 213-393 m 2 g 21 ). Their thermal conductivity (0.041 W m 21 K 21 ) is comparable to that of glass wool. Hydrophobicity, however, is the property that sets the new material apart from analogous polyurea and epoxy crosslinked aerogels. The contact angles of water droplets on disks cut from larger monoliths are >120u. (By comparison, the contact angle with polyurea crosslinked aerogels is only ca. 60u.) Polystyrene crosslinked aerogel monoliths float on water indefinitely, while their polyurea counterparts absorb water and sink within minutes.