No abstract

Biodegradable polylactic acid (PLA) was compounded with thermoplastic polyurethane (TPU) by twin-screw extrusion at weight ratios of 90/10, 80/20, 70/30, and 60/ 40. The blends were investigated based on their phase morphology, thermal and mechanical properties, and shape memory properties. The tensile results showed that PLA was successfully toughened by TPU. When the TPU content was 40%, the elongation-at-break increased to 400%. The SEM morphology showed that TPU was dispersed uniformly in the PLA matrix; DMA and DSC results indicated that the two polymers were immiscible. Most interestingly, it was found that the blends exhibited a shape memory behavior and, unlike most of the existing shape memory polymers (SMPs), the PLA/TPU blends could be deformed at room temperature without an extra heating and cooling step. During the deformation process,

Superhydrophobic poly(vinyl alcohol) (PVA)/cellulose nanofibril (CNF) aerogels with a unidirectionally aligned microtubular porous structure were prepared using a unidirectional freeze-drying process, followed by the thermal chemical vapor deposition of methyltrichlorosilane. The silanized aerogels were characterized using various techniques including scanning electron microscopy (SEM), Fourier transform infrared spectroscopy, and contact angle measurements. The structure of the aerogels fully filled with polydimethylsiloxane (PDMS) was confirmed by SEM and optical microscopy. The mechanical properties of the resulting PDMS/aerogel composites were examined using both compressive and tensile tests. The compressive and tensile Young's moduli of the fully filled PDMS/aerogel composites were more than 2-fold and 15-fold higher than those of pure PDMS. This study provides a novel alternative approach for preparing high performance polymer nanocomposites with a bicontinuous structure.

A novel polydimethylsiloxane (PDMS)/cellulose nanocrystal flake (CNCF) composite triboelectric nanogenerator (CTG) using CNCFs as effective dielectrics exhibited a 10-times-enhanced triboelectric performance compared with its pure PDMS counterpart. Positive charges generated on the surface of the CNCFs during cyclic compression boosted electron transfer and induced extra charges. The CTG exhibited an instantaneous output power (density) of 1.65 mW (0.76 mW cm) under continuous operation.

Varying the processing conditions of semicrystalline polymers can produce different morphologies of crystallization, which leads to different properties. There have been extensive studies of flow-induced crystallization on isotactic polypropylene (iPP) using predominantly shear flow. A stretching method, deduced from extrusion, was introduced to study the morphological evolution of elongation-induced shish-kebab crystallization. Different morphologies of the resultant samples with different draw ratios (DRs) were carefully investigated and characterized via differential scanning calorimetry, polarizing light microscopy, scanning electron microscopy, atomic force microscopy, and 2D small-angle X-ray scattering. In addition, the degree of orientation of the samples with different DRs was also investigated using the 2D wide-angle X-ray scattering technique. The results indicate that the elongationinduced morphology is strongly dependent on the effective stretching flow expressed in terms of the DR, which is defined

The effects of nanoclay on the crystallization behavior, microcellular structure, and mechanical properties of thermoplastic polyurethane (TPU)/clay nanocomposite (TPUCN) foams were investigated using differential scanning calorimetry, rheometry, scanning electron microscope, transmission electron microscopy, and X‐ray diffraction. It was found that the nanoclay acted as an effective nucleating agent for both crystal nucleation and cell nucleation. As a result, it significantly enhanced the crystallization behavior of the hard segment (HS) domains in TPU while refining the foamed structure of the microcellular injection molded parts. In particular, the average cell diameter of TPUCN foams decreased from 45 µm for neat TPU to 27 µm for TPUCN5 (5 wt% clay) and 18 µm for TPUCN10 (10 wt% clay). Furthermore, the cell density increased from 0.7 × 107 cell/cm3 for neat TPU to 1.4 × 107 cell/cm3 and 3.1 × 107 cell/cm3 for TPUCN5 and TPUCN10, respectively. In addition, the tensile strength also increased by 56.3% and 89.2% with 5 and 10 wt% clay content, respectively. By controlling the cell nucleation behavior through uniformly dispersed nanoclay, this study demonstrates that it is feasible to produce TPUCN foams via microcellular injection molding with desirable microcellular structures and improved mechanical properties. POLYM. ENG. SCI., 56:319–327, 2016. © 2015 Society of Plastics Engineers

In this study, biomedical thermoplastic polyurethane/ graphene oxide (TPU/GO) composite scaffolds were successfully prepared using the thermally induced phase separation (TIPS) technique. The microstructure, morphology, and thermal and mechanical properties of the scaffolds were characterized by Fourier transform infrared spectroscopy (FTIR), Raman spectroscopy, scanning electron microscopy (SEM), differential scanning calorimetry (DSC), thermal gravimetric analysis (TGA), and compression tests. Furthermore, NIH 3T3 fibroblast cell viability on the porous scaffolds was investigated via live/dead fluorescent staining and SEM observation. FTIR and Raman results verified the presence of GO in the composites. SEM images showed that the average pore diameter of the composite scaffolds decreased as the amount of GO increased. Additionally, the surface of the specimens became rougher due to the embedded GO. The compressive modulus of composite specimens was increased by nearly 200% and 300% with the addition of 5% and 10% GO, respectively, as compared with pristine TPU. 3T3 fibroblast culture results showed that GO had no apparent cytotoxicity. However, high loading levels of GO may delay cell proliferation on the specimens.

This study was aimed at understanding how the process conditions affect the weld‐line strength and microstructure of injection molded microcellular parts. A design of experiments (DOE) was performed and polycarbonate tensile test specimens were produced for tensile tests and microscopic analysis. Injection molding trials were performed by systematically adjusting four process parameters (i.e., melt temperature, shot size, supercritical fluid (SCF) level, and injection speed). For comparison, conventional solid specimens were also produced. The tensile strength was measured at the weld line and away from the weld line. The weld‐line strength of injecton molded microcellular parts was lower than that of its solid counterparts. It increased with increasing shot size, melt temperature, and injection speed, and was weakly dependent on the supercritical fluid level. The microstructure of the molded specimens at various cross sections were examined using scanning electron microscope (SEM) and a light microscope to study the variation of cell size and density with different process conditions.