Today's consumer electronics, such as cell phones, tablets and other portable electronic devices, are typically made of non-renewable, non-biodegradable, and sometimes potentially toxic (for example, gallium arsenide) materials. These consumer electronics are frequently upgraded or discarded, leading to serious environmental contamination. Thus, electronic systems consisting of renewable and biodegradable materials and minimal amount of potentially toxic materials are desirable. Here we report high-performance flexible microwave and digital electronics that consume the smallest amount of potentially toxic materials on biobased, biodegradable and flexible cellulose nanofibril papers. Furthermore, we demonstrate gallium arsenide microwave devices, the consumer wireless workhorse, in a transferrable thin-film form. Successful fabrication of key electrical components on the flexible cellulose nanofibril paper with comparable performance to their rigid counterparts and clear demonstration of fungal biodegradation of the cellulose-nanofibril-based electronics suggest that it is feasible to fabricate high-performance flexible electronics using ecofriendly materials.

No abstract

PVA/CNF aerogels produced by an environmentally friendly freeze-drying process followed by thermal chemical vapor deposition of methyltrichlorosilane exhibit excellent oil and solvent absorption and remarkable heavy metal ion scavenging capability.

A novel type of highly flexible and all-solid-state supercapacitor that uses cellulose nanofibril (CNF)/reduced graphene oxide (RGO)/carbon nanotube (CNT) hybrid aerogels as electrodes and H2SO4/poly(vinyl alcohol) (PVA) gel as the electrolyte was developed and is reported here. These flexible solid-state supercapacitors were fabricated without any binders, current collectors, or electroactive additives. Because of the porous structure of the CNF/RGO/CNT aerogel electrodes and the excellent electrolyte absorption properties of the CNFs present in the aerogel electrodes, the resulting flexible supercapacitors exhibited a high specific capacitance (i.e., 252 F g(-1) at a discharge current density of 0.5 A g(-1)) and a remarkable cycle stability (i.e., more than 99.5% of the capacitance was retained after 1000 charge-discharge cycles at a current density of 1 A g(-1)). Furthermore, the supercapacitors also showed extremely high areal capacitance, areal power density, and energy density (i.e., 216 mF cm(-2), 9.5 mW cm(-2), and 28.4 μWh cm(-2), respectively). In light of its excellent electrical performance, low cost, ease of large-scale manufacturing, and environmental friendliness, the CNF/RGO/CNT aerogel electrodes may have a promising application in the development of flexible energy-storage devices.

A novel class of high performance polymer porous aerogel film‐based triboelectric nanogenerators (A‐NGs) is demonstrated. The A‐NGs, made of a pair of highly porous polymer films, exhibit much higher triboelectric outputs than the corresponding dense polymer film‐based triboelectric nanogenerators (D‐NGs) under the same mechanical stress. The triboelectric outputs of the A‐NGs increase significantly with increasing porosity, which can be attributed to the increase in contact area and the electrostatic induction in the porous structure, thereby leading to additional charges on the porous surface. Remarkably, the A‐NG fabricated using porous chitosan aerogel film paired with the most porous polyimide (with a porosity of 92%) aerogel film demonstrates a very high voltage of 60.6 V and current of 7.7 µA, corresponding to a power density of 2.33 W m−2, which is sufficient to power 22 blue light‐emitting‐diodes (LEDs). This is the first report on triboelectric nanogenerators (TENGs) employing porous polymer aerogel films as both positive and negative materials to enhance triboelectric outputs. Furthermore, enhancing the tribopositive polarity of the cellulose aerogel film via silanization using aminosilane can dramatically improve the triboelectric performance. Therefore, this study provides new insights into investigating porous materials with tunable triboelectric polarities for high performance TENGs.

No abstract

Hybrid organic aerogels consisting of polyvinyl alcohol (PVA), cellulose nanofibrils (CNFs), and graphene oxide nanosheets (GONSs) were prepared using an environmentally friendly freeze-drying process. The material properties of these fabricated aerogels were measured and analyzed using various characterization techniques including compression testing, scanning electron microscopy, thermogravimetric (TGA) analysis, Brunauer-Emmet-Teller (BET) surface area analysis, and contact angle measurements. These environmentally friendly, biobased hybrid organic aerogels exhibited a series of desirable properties including a high specific compressive strength and compressive failure strain, ultralow density and thermal conductivity, good thermal stability, and moisture resistance, making them potentially useful for a broad range of applications including thermal insulation.

Aqueous Na‐ or K‐ion batteries could virtually eliminate the safety and cost concerns raised from Li‐ion batteries, but their widespread applications have generally suffered from narrow electrochemical potential window (ca. 1.23 V) of aqueous electrolytes that leads to low energy density. Herein, by exploring optimized eutectic systems of Na and K salts with asymmetric imide anions, we discovered, for the first time, room‐temperature hydrate melts for Na and K systems, which are the second and third alkali metal hydrate melts reported since the first discovery of Li hydrate melt by our group in 2016. The newly discovered Na‐ and K‐ hydrate melts could significantly extend the potential window up to 2.7 and 2.5 V (at Pt electrode), respectively, owing to the merit that almost all water molecules participate in the Na+ or K+ hydration shells. As a proof‐of‐concept, a prototype Na3V2(PO4)2F3|NaTi2(PO4)3 aqueous Na‐ion full‐cell with the Na‐hydrate‐melt electrolyte delivers an average discharge voltage of 1.75 V, that is among the highest value ever reported for all aqueous Na‐ion batteries.