BackgroundHuman papilloma virus (HPV) infection was the main cause of cervical cancer. There were only a few reports and detailed data about epidemiological research of HPV infection in rural population of China.Materials and MethodsThe cervical cells of rural Chaozhou women were collected, and multiplex real time PCR was firstly performed to detect high-risk HPV (HR-HPV) infection, which could detect 13 types of HR-HPV (types 16, 18, 31, 33, 35, 39, 45, 51, 52, 56, 58, 59, and 68). Then, HPV-positive samples were typed by HPV GenoArray test.ResultsHR-HPV DNA was detected by multiplex real time-PCR in 3830 of 48559 cases (7.89%). There was a peak incidence in age of 55–60 years group, and a lower incidence in who lived in plain group compared with suburban, mountain and seashore group. 3380 cases of HPV positive sample were genotyped, 11.01% (372/3380) cases could not be classified, among the typed 3008 cases, 101 cases were identified without HR-HPV type infection, 2907 cases were infected with one HR-HPV type at least, the 6 most common HR-HPV types in descending order of infection, were type 52 (33.4%, 16 (20.95%), 58 (15.93%), 33 (9.94%), 68 (9.22%) and 18 (8.36%). The combined prevalence of HPV types 16 and 18 accounted for 28.52% of total infection. However, type 52 plus 58 presented 48.23% of total infection. 2209/2907 cases were infected with a single HPV type and 698/2907 cases were infected with multiple types, and multiple infection constituent ratio increased with age, with a peak incidence in age 55–60 years group.ConclusionsOur findings showed low prevalence of HPV vaccine types (16 and 18) and relatively high prevalence of HPV-52 and -58, support the hypothesis that the second-generation HPV vaccines including HPV-52 and -58 may offer higher protection for women in rural Guangdong Province.

Our results showed that the HPV prevalence in Guangdong is very similar to the world level. Unlike most previous studies, our findings suggest that HPV prevalence increased with age, and that the predominant genotypes in this area were HPV 52 and 58.

BackgroundThe emerging Coronavirus Disease-2019 (COVID-19) has challenged the public health globally. With the increasing requirement of detection for SARS-CoV-2 outside of the laboratory setting, a rapid and precise Point of Care Test (POCT) is urgently needed.MethodsTargeting the nucleocapsid (N) gene of SARS-CoV-2, specific primers, and probes for reverse transcription recombinase-aided amplification coupled with lateral flow dipstick (RT-RAA/LFD) platform were designed. For specificity evaluation, it was tested with human coronaviruses, human influenza A virus, influenza B viruses, respiratory syncytial virus, and hepatitis B virus, respectively. For sensitivity assay, it was estimated by templates of recombinant plasmid and pseudovirus of SARS-CoV-2 RNA. For clinical assessment, 100 clinical samples (13 positive and 87 negatives for SARS-CoV-2) were tested via quantitative reverse transcription PCR (RT-qPCR) and RT-RAA/LFD, respectively.ResultsThe limit of detection was 1 copies/μl in RT-RAA/LFD assay, which could be conducted within 30 min at 39°C, without any cross-reaction with other human coronaviruses and clinical respiratory pathogens. Compared with RT-qPCR, the established POCT assay offered 100% specificity and 100% sensitivity in the detection of clinical samples.ConclusionThis work provides a convenient POCT tool for rapid screening, diagnosis, and monitoring of suspected patients in SARS-CoV-2 endemic areas.

No abstract

Precise micro-grinding machining was proposed to fabricate regular and controllable micro-grooved array structures on the surface of mold cores to realize the mass production and manufacturing of micro-structured polymer components by micro injection molding in this paper. First, the 3D topographies and section profiles of micro-ground mold cores and micro-formed polymers with different micro-structure parameters were presented. Then, the surface roughness of mold cores and polymers were compared. Next, the relationships between machining accuracy of mold core ground by micro-grinding and filling rates of micro-structured polymer formed by micro injection molding were investigated. Finally, the influences of micro injection molding parameters on the filling rate of micro-structures polymer were investigated. It is shown that the micro-structured polymer can be effectively and rapidly fabricated using the proposed method. The experimental results indicate the highest form accuracy of the micro-grooved mold core and the filling rate of micro-structured polymer can reach to 4.05 µm and 99.30%, respectively. It is found that the filling rate of the micro-structured polymer roughly increased with increasing machining accuracy of the mold core. The injection pressure had the greatest influence on the filling rate of the injection formed polymer, while the melt temperature had the least influence.