Organic semiconductor materials have been the center of attention because they are scalable, low-cost for device fabrication, and they have good optical properties and mechanical flexibility, which encourages their research. Organic field-effect transistors (OFETs) have potential applications, specifically in flexible and low-cost electronics such as portable and wearable technologies. In this work we report the fabrication of an InClPc base flexible bottom-gate/top-contact OFET sandwich, configured by the high-evaporation vacuum technique. The gate substrate consisted of a bilayer poly(ethylene terephthalate) (PET) and indium–tin oxide (ITO) with nylon 11/Al2O3. The device was characterized by different techniques to determine chemical stability, absorbance, transmittance, bandgap, optical properties, and electrical characteristics in order to determine its structure and operational properties. IR spectroscopy verified that the thin films that integrated the device did not suffer degradation during the deposition process, and there were no impurities that affected the charge mobility in the OFET. Also, the InClPc semiconductor IR fingerprint was present on the deposited device. Surface analysis showed evidence of a nonhomogeneous film and also a cluster deposition process of the InClPc. Using the Tauc model, the device calculated indirect bandgap transitions of approximately 1.67 eV. The device’s field effect mobility had a value of 36.2 cm2 V−1 s−1, which was superior to mobility values obtained for commonly manufactured OFETs and increased its potential to be used in flexible organic electronics. Also, a subthreshold swing of 80.64 mV/dec was achieved and was adequate for this kind of organic-based semiconductor device. Therefore, semiconductor functionality is maintained at different gate voltages and is transferred accurately to the film, which makes these flexible OFETs a good candidate for electronic applications.

The synthesis of four mononuclear heptacoordinated organotin (IV) complexes of mixed ligands derived from tridentated Schiff bases and pyrazinecarboxylic acid is reported. This organotin (IV) complexes were prepared by using a multicomponent reaction, the reaction proceeds in moderate to good yields (64% to 82%). The complexes were characterized by UV-vis spectroscopy, IR spectroscopy, mass spectrometry, 1H, 13C, and 119Sn nuclear magnetic resonance (NMR) and elemental analysis. The spectroscopic analysis revealed that the tin atom is seven-coordinate in solution and that the carboxyl group acts as monodentate ligand. To determine the effect of the substituent on the optoelectronic properties of the organotin (IV) complexes, thin films were deposited, and the optical bandgap was obtained. A bandgap between 1.88 and 1.98 eV for the pellets and between 1.23 and 1.40 eV for the thin films was obtained. Later, different types of optoelectronic devices with architecture “contacts up / base down” were manufactured and analyzed to compare their electrical behavior. The design was intended to generate a composite based on the synthetized heptacoordinated organotin (IV) complexes embedded on the poly(3,4-ethylenedyoxithiophene)-poly(styrene sulfonate) (PEDOT:PSS). A Schottky curve at low voltages (<1.5 mV) and a current density variation of as much as ~ 3×10−5 A/cm2 at ~ 1.1 mV was observed. A generated photocurrent was of approximately 10−7 A and a photoconductivity between 4×10−9 and 7×10−9 S/cm for all the manufactured structures. The structural modifications on organotin (IV) complexes were focused on the electronic nature of the substituents and their ability to contribute to the electronic delocalization via the π system. The presence of the methyl group, a modest electron donor, or the non-substitution on the aromatic ring, has a reduced effect on the electronic properties of the molecule. However, a strong effect in the electronic properties of the material can be inferred from the presence of electron-withdrawing substituents like chlorine, able to reduce the gap energies.

It is known that one factor that affects the operation of optoelectronic devices is the effective protection of the semiconductor materials against environmental conditions. The permeation of atmospheric oxygen and water molecules into the device structure induces degradation of the electrodes and the semiconductor. As a result, in this communication we report the fabrication of semiconductor membranes consisting of Magnesium Phthalocyanine-allene (MgPc-allene) particles dispersed in Nylon 11 films. These membranes combine polymer properties with organic semiconductors properties and also provide a barrier effect for the atmospheric gas molecules. They were prepared by high vacuum evaporation and followed by thermal relaxation technique. For the characterization of the obtained membranes, Fourier-transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), and energy dispersive spectroscopy (EDS) were used to determine the chemical and microstructural properties. UV-ViS, null ellipsometry, and visible photoluminescence (PL) at room temperature were used to characterize the optoelectronic properties. These results were compared with those obtained for the organic semiconductors: MgPc-allene thin films. Additionally, semiconductor membranes devices have been prepared, and a study of the device electronic transport properties was conducted by measuring electrical current density-voltage (J-V) characteristics by four point probes with different wavelengths. The resistance properties against different environmental molecules are enhanced, maintaining their semiconductor functionality that makes them candidates for optoelectronic applications.

No abstract