No abstract

Pitch-faced concrete is becoming a very popular element of modern architecture in the 21st century. In particular, the demand for concrete facades is increasing globally. On the other hand, climate change, environmental degradation, and limited resources are motivations for sustainable building materials. The construction industry is one the highest emitters of CO2 and other greenhouse gases, in which concrete plays a major role. Thus, reduction in the volume of concrete consumption is essential to control greenhouse gases. One approach to this problem is to use textile reinforced concrete (TRC). The main aim of the present study was to compare the subtle TRC facade made of three different types of technical textile rovings (glass, carbon, and basalt) with ordinary facades reinforced by steel reinforcement (ORC). The goal was to compare the basic environmental impact potential according to product category rules (PCR) for concrete structures. The functional unit was defined as an experimental facade with an area of 60 m2 and a 100-year lifespan. Inventory data were elaborated for concrete, steel, and textile fiber production; the building site; service life; demolition; and final disposal. The main life cycle assessment (LCA) parameters were global warming potential (GWP), ozone depletion (ODP), acidification (AP), eutrophication (EP), abiotic depletion (ADP), and photochemical oxidant creation (POCP). All the data used in the work were related to Czech Republic. Textile reinforced concrete facades appeared to be more environmentally friendly in four of six impact categories by an average of 30%. The results of the present study revealed that, in comparison to ORC, TRC has a lower environmental impact for the given conditions and thus good potential for use in sustainable construction.

Textile-reinforced concrete (TRC) is a material that is gaining new ground in the field of construction where it not only allows for the manufacture of reduced lightweight structures but also eliminates the problem of corrosion by using alkali-resistant textile reinforcement. The aim of this paper is to investigate the bending behaviour of a newly developed TRC facade panel that incorporates polystyrene foam prisms. Numerical simulations were employed in order to choose the geometry and repartition of prisms inside the facade panel. Experimental results revealed a reduced amount of concrete by 20% via the use of rigid foam prisms with a higher failure load by 16% but a lower elasticity limit by 49% in comparison with the regular facade panels.

No abstract

High performance concrete reinforced by technical textiles has found a wide range of applications in recent years. One of the most widespread is the use of this composite for the very thin facade panels of various shapes and technical solutions. This paper presents an unique way how to lighten the facade panels made of high performance concrete (HPC) reinforced by technical textiles, which are additionally equipped with LEDs, so that a sufficient distance can be watch programmed based image displays.

Use of high performance concrete with reinforcement made of technical textile is increasing and new applications are being found. This paper presents new technology for the lightening of the panels made of textile reinforced concrete, which is being developed. The main focus of this research is to produce concrete elements suitable for use as facade panels with the least possible weight and environmental impact. Mechanical characteristics were measured on testing specimens with thickness of 18 mm with lightening representing 47% of their volume. Minimum thickness of concrete was 4 mm and therefore the reinforcement was covered by approximately 1.5 mm of concrete matrix. The strength of experimental test panels was measured in four-point bending stress test. Due to one-sided lightening and asymmetrical cross-section therefore, the tests were performed in both directions. For better interpretation of the results were the specimens of lightened panels tested alongside non-lightened specimens with the same thickness. Based on measured values, maximal dimensions of lightened facade panels were designed.

This article deals with optimal dosage of metakaolin as addition in high performance concrete. The main criteria for assessing the optimal dosage of metakaolin was compressive strength, rheological behaviour and economic benefits. Metakaolin was added to the mixture of high performance concrete in the range from 0 to 25% weight of cement. The comparison of metakaolin and microsilica, which is often used by concrete producers due to its excellent properties, is also performed in this article. The experiments showed that using metakaolin as addition in high performance concrete affects the compressive strength and rheological behaviour positively. While the compressive strength increases especially at lower doses of metakaolin and at higher doses remained unchanged, changes in rheological behaviour were most obvious at the higher doses. From this point of view, it is possible to recommend a higher dose of metakaolin.

Development of extremely thin concrete structures and demand for extremely thin elements are the reason of using composite non-traditional materials as reinforcement. Steel reinforcement is not very chemically resistant and it limits the thickness because of the required concrete cover as protection. This is the reason why textile reinforced concrete (TRC) going to be very famous and modern material. TRC in combination with fine grain high performance concrete (HPC) allows a significant saving of concrete. Due to its non-corrosive properties of composite technical textiles it is possible to design very subtle structures and elements. TRC and HPC in general are developed at the Faculty of Civil Engineering and the Klokner Institute, CTU in Prague. This present paper investigates the cohesion influence of textile reinforcement on four point bending test. All small experimental panels were reinforced with the same 3D technical textile from AR-glass roving with different type of cover layer. Different conditions of interaction between technical textiles and HPC were ensured by modified surface using silica sand and silica flour.